I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello!
(SDK15, nrf52832, SES)
I started to implement DFU in my code following this tutorial . So far with the tutorial i have the following issue.
1. In the section...
I have downloaded nRF SDK for Mesh version 2.2.0 and nRF5 SDK version 15.0. I am running examples(serial) from Mesh ver 2.2.0 and getting error such as no such file/directory...
I want to establish mesh connection between 3 nRF 52840 dongles. For this I have to use nRF connect Mesh desktop software for windows or is there any other way. I want to...
There is a notable bug with nRF52-DK with arduino framwork, as you can see on github here (see the point 7), click on this link : #33 (comment)
The problematic code is here...
Hello there,
In this link, there is a table saying which version of SDK and SoftDevice may be used with any IC revision:
http://infocenter.nordicsemi.com/index.jsp?topic...
hello there!
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller nRF51822 for connection and data...
Hi,
1. I'm developing multiprotocol BLE/Thread app with Thread SDK 1.0 and I want to ask if there's a possibilty to perform DFU over Thread in that case? In Thread Secure...
Hello,
In past I worked with BLE 4.0 and I remember that using the notify we have a max amount of data of 20 bytes.
Now we are working with BLE 4.2, does we have this...
The nRF Mesh Connect software available from this blog post is probably corrupted. I am not able to use it. Is there a repository for software tools where I could download...
Hi,
I am using sdk 12 with s132 v3 on nrf52832 dev board. I am running the example code for ble hid peripheral for keyboard compiled using gcc and eclipse. The example code...
Hi,Sir:
I am developing a 52840’s project using SDK15.1,My development environment is Segger embedded (version 3.34a).When I added the RNG function to the code (the correct...
Hi,
Have an issue with a prototype 2 layer 52840 pcb that i tried to get manufactured. i increased the pad diameter to 0.3mm and now i cannot route without hitting clearance...
Hi
when trying https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library everything goes OK (I think...) all the nodes gets provisioned, all the elements gets addresses...
I know the PDK design is available for download, but there are a lot of things on that board which would not be required for a minimal e.g. beacon design
I'm looking for...
