I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi all,
On SDK 15.0, Immediate Alert Service is not working without a secured BLE link. When peripheral is not paired, this latter doesn't receive any alert from central...
I’m using SDK 15.0.0. and softdevice 6.0.0.
When I compile the example:
https://github.com/haakonsh/MMD
I get the compiler error:
fatal error: compiler_abstraction...
Hi,
I tried ble_app_uart example by using SES it works fine. Then I tried it by using eclipse with OpenOCD and a STlink V2 on the debug in port I succeeded to flash it....
Hey guys,
With the new SDK15, I find myself looking at dependency problems over and over again. Right now, I am trying to setup a simple A/D conversion using nrfx_adc. Found...
Hi Env: keil uvision 5 and SDK 9 and custome breakoutboard for nRF51822 (PTR5518: no external crystal) and no SD.
I am trying doing the first steps in twi over nRF51822...
I been reading over your entire tutorials, but I have yet to see any tutorials that guides me towards creating an NRF52 project from scratch? Could anyone guide me through...
Hi,
I am transferring my nrf52832 project to nrf52810,and I have deploy the project according to the user guide (Transferring the project to nRF52810 hardware),
when I...
Hello everyone,
I'm developing an application for boards with NRF52832, Softdevice S132 3.00 and SDK 12.3.0.
The network architecture consists of:
one peripheral board...
I'm using my accelerometer's GPIO interrupt to wake up the MPU from PowerOFF mode and it works great. Now, I'm trying to use the same interrupts to wake it up from Sleep mode...
Hi,
I have migrated from SDK14.1 to SDK15.
One thing is embarrassing me.
I would like to modify the scan data as above, I do not know where I can fix it.
phy...
Hi,
I am using mbedos for a NRF42832 and am currently in the situation that I have to profile my code with gprof. Here comes the issue: the Nordic SDK uses explicit assembler...
this picture is from infocenter.nordicsemi.com/index.jsp
and this picture is from 《S132_SDS_v5.0.pdf》
in first picture the application base is 0x00020000 , in...
I've been instrumenting my Nordic app with RTT logging, which has been working great up until now. I use the deferred mode and use nrf_log_push() to queue all dynamic strings...
For the connection event collision, I have some doubts, I hope to get help in devzone
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.s132.sds...
Hi, everyone,
We develop BLE project including DFU bootloader.
But to use the standard bootloader "as is" it is not possible for us. Due to this problem we must make some...
