I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
We try to implement DFU over UART. The Mesh DFU example has been taken as a reference. DFU is successful, but it takes about 1 hour (sic!) to transfer DFU ZIP package of size...
Hi,
We are developing a device which should have a power save mode where no BLE connection is possible (switch off the BLE to a minimum power consumption) and restart the...
Hi, there~~ Just noticed that there are codes for the Android nRF connect.
github.com/.../Android-nRF-Connect
Using that code, I wish to create my personal sniffer that...
Good afternoon,
I'm using nRF52840 with SDK15 and Softdevice6.0.0.
I'm using the Queued Write Service Module to make use of a characteristic able to receive up to 510bytes...
Please suggest a tool that can be used for monitoring and and analysis of Nordic's BLE packet transmission rate.
I would like to measure packet irregularities over time...
HI,
How to use sd_ble_opt_set() with the option BLE_GAP_OPT_SCAN_REQ_REPORT ? After setting this I can expect to get the event "BLE_GAP_EVT_SCAN_REQ_REPORT" with information...
Hi,Support Team
I Use the nRF51822 SOC for SDK12.3-example-DFU-bootloader_secure, when I Select the ZIP upadate file,it has a reminder "Loading file has failed. Try different...
Hi,
I use buttonless DFU with the secure bootloader.
When I push a button my application advertise in fast mode with an interval of 40ms and for 5s. After it return to...
SEGGER Embedded Studio Release 3.40 Build 2018052200.36079
The so-called "flash (sic?) placement" XML file contains two sections:
First:
which does, indeed, seem...
Hello, I am currently working on a nr52840 s140 Sdk 15.0 card and I want to recover data from a component running on the i²c bus. (I have not yet installed the component on...
Hello,
I would like to know if it is possible to use a nRF52840 as bridge between ethernet and 802.15.4/thread. For a sensor network I need an ip connection between multiple...
Hi,
I'm using nRF52 DK. I was checking the message sent by NRF_LOG_INFO() on Termite. I'm getting driver error when I try to connect to laptop's bluetooth.
Without the...
Hello
what is the maximum limit for PWM outputs pins on nrf52832? Can we use all the GPIO pins as a PWM output?
For ADC, i can see there are 8 dedicated pins , but i...
hello i am beginner in this,i am using example\ peripherals\ saadc for nrf 52832. This example code is done by using timer and i could not understand how to use timer. We...
