Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
For a new project I am using the Decawave module DWM1001. This module is equipped with an NRF52832. I have already used the nrf52832 for previous project and I face...
Hi there,
Is there a specific sequence needed to power-up the NRF52840?
Let me get into the details:
My design uses configuration #5 from the datasheet (see below...
Hi, I'm using the serial example from the nRF5 SDK for Mesh (version 2.2.0) and after running it for extended time with data being received from nodes every few seconds, it...
I have a small app_usbd demo which works fine on the nrf52 dongle, but not on the larger nrf52840-dk.
I am running SDK 15.0 with the errata fix mentioned on several other...
ATT MTU THROUGHTPUT EXAMPLE FOR nRF52810 on KEIL using S132 v5.1.0 PLEASE >>>>>>>>>>>>>
Tried this : https://devzone.nordicsemi.com/b/blog/posts/the-s132-v5-1-0-is-now...
Hi!
I am currently developing product containing Thread mesh and BLE peripheral service. I am using Thread SDK v2 in my software. My application has to support writing to...
Is there any NRF51822 DFU guide under following conditions:
a. NRF51822
b. SDK11.0.0
c. Dual Bank BLE DFU(\examples\dfu\bootloader\pca10028\dual_bank_ble_s130\)
I...
Hello i am working with light switch proxy client server sdk example.i make provision light and switch using nrf mesh application.i have three nrf52832 dk board.i flashed...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
I tried to create a descriptor for a characteristic. I modified the app_blinky and added a ble_add_descr_params_t variable. After The Initialisation and definition of the...
Hi,
I've tried blink,hid,uart,template similar sdk examples so far. Now i acquired some experience about nrf52832 processor and bluetooth,but ii don't really have enough...
I have had an issue recently with some beacons that I am using to log temperature data. A portion of the beacons drained their batteries very quickly and didn't respond to...
Hi I have this piece of code which works in SDK 12 but when I port it to SDK 15 the sd_ble_gatts_characteristic_add function would fail with an error code of 7. No change...
Hi,
I want to put my nrf52832 into the low-power mode. I select SYSTEM ON with low-power (instead of SYSTEM OFF) in order to overcome reset. In order to do it I call sd_app_evt_wait...
