In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
I've used PCA10040 sdk15.0 example ble_peripheral ble_app_uart
I can handle it through terminal.
If I insert strings through terminal, App can receive.
But, I...
hii,
i am trying to interface the nrf24LU1+ and nrf52832. I wanted to know if i can program the nrf24lu1+ without the requirement of nrfgo motherboard. or is it necessary...
I don't want to use MESH， because there are too many data
Application scenario
Mobile phone ------------> DeviceA --------------------------------------> DeviceB
...
Hello,
Would there be any particularly adverse side-effect if two NRF51822 GPIO pins (e.g., P0.18 and P0.19) were shorted together? One of the pins (e.g., P0.18) would be...
SDK ：15.0.0
Examples：ble_peripheral / ble_app_uart / pca10056 / s140
Board：nRF52840 DK
After pairing, may be connected, because the indicator lights continue to shine...
Hi,
I am using sd_ble_gatts_characteristic_add to set a characteristic in my service. The function call return 0 - NRF_SUCCESS but when I browse the service with nRF connect...
Hello,
I try to add pairing functionality to my app. Error code NRF_ERROR_INVALID_PARAM occur from the sd_ble_gap_sec_params_reply when i want to read my characteritic...
Hey, I have a sensor (ADC with data rate is 250 sps), attached to nrf51822. It has Data ready pin (output), which toggles from high to low when data is ready. Also this sensor...
Hi, I'm using nRF52832 with my custom board. (sdk 15.0.0)
I changed ble_uart example code, so I can receive GPS data through bluetooth.
Now, I have to send GPS data to...
Hello all.
few years ago, I made some product using nRF51822 on SDK v10.0.0
currently, I have to software update to use ECC(Elliptic Curve Cryptography) function on...
I'm using: nrf52832, SDK 15.0, SoftDevice S132 v6.0.
I'm trying to control a motor using an H-Bridge. If I simply do a nrf_gpio_pin_write to set forward/reverse to 1/0 or...
I have the nRF52832 PCA10040, V1.2.1, 2017.23 development board with ble_app_blinky_gcc_nrf52.ld RAM/FLASH settings:
MEMORY { FLASH (rx) : ORIGIN = 0x26000, LENGTH = 0x5a000...
Hi,
My freertos based application (SDK14.2) calls battery monitoring procedure every few minutes .
I've initialized the SAADC
Within the function I call
...
Hello, I have nrf52 and configure uart0 for connection with external device. I have configured it as NRF_SERIAL_MODE_DMA and set irq_handler .receive NRF_SERIAL_EVENT_DRV_ERR...
