I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I am using Segger embedded studio 3.1 with SD132 2.0.0 and a nRF52832QFAAB0.
I have verified that I am compiling against the correct header files. This service number for...
Hi, even if I set hal_nrf_enable_ack_payload(false) on the sender (and receiver), the receiver still sends back an ACK which i can detect in the NRF_ISR(). is this normal...
Hello,
I have a pca10028 and I am wondering if I can use it also to flash nrf52 boards.
I quickly tried with rknrfgo on mac to wipe a custom board based on nRF52832 and...
Hello.
I decided to use an external solution for RTC.
Sometimes the RTC chip offers an buffered 32.768KHz output.
Can I use this output to supply the 32.768KHz to the nRF52832...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hai
i am using mbed to program my nrf5188. now i am using securityManager to implement a bonding between central and peripheral. now i need to know when a device is connected...
Hi,
In my code, I have not started the HF clock. I call the ble_stack_init where "SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);" is called. Which HF clock...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
The ble_app_uart includes "printf("\r\nUART Start!\r\n");" and "UART Start!" cames out on the putty...
I have a scenario where I have multiple peripherals (nRF52) and multiple centrals (cell phone).
The user is going to use only one central with only one peripheral together...
Hello
In case a connection is disconnected locally by calling sd_ble_gap_disconnect(), no BLE_GAP_EVT_DISCONNECTED is fired even though the sd_ble_gap_disconnect() function...
Hello, I'm trying to optimize power on HID Keyboard app.
This post was helpfull but yet some questions remains.
If I use several services, and want central to be abble...
After S110 7.1 ble_stack_init(), any read/write to temperature register cause a HardFault.
Some sentences like:
nrf_temp_init();
NRF_TEMP->TASKS_START = 1;
...
Hi --
I am using the ble_peripheral/ble_app_hrs example project. And if I try to update the vs_uuid_count param to 2. It proceeds to fail the softdevice_enable with error...
