Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
nrfutil install fail.
I want to update with BLE secure OTA, so install the nrfutil tool. and run the command as following:
but report download pc-ble-driver-py 0...
Total noob here using SES on a Mac to build BLE peripheral (S110) firmware for an nRF51822-based device with SDK v15.
So far I've been able to get the generic portions of...
Hi,
I'm developing on nrf52810 using the SDK14.1.0 and I've take as starting point a template application that targets nRF52810 running on the nRF52 Development Kit. But...
Taking a look through the SDK, there are very few examples using the dongle. I've tried building some of the existing examples by changing the board definition in the preprocessor...
I have a porject working well with normal ble function such as ancs and other services（use sdk15.0） , when I add the mesh model light switch on_off (source code copy from...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project for get thingy motion data by nRF52840.
But It still found 6 Service for motion service,...
I have a use case where I need to send a sequence of 2 byte bursts as SPI master. The data is generated on the fly and the algorithm would be able to saturate the 8Mbit/s...
Hi,
I just installed nrf connect 1.1 on my Dev-PC (many versions of J-Link and nrfjprog) everything works fine. The visualization of Secure-DFU-Upload-Speed is really nice...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
PDK: PCA10040
I am trying to read the ADC pin value using the SAADC module, I...
Hi, I'm using external board with nRF52832. (SDK 15.0.0)
In my external board, there are no RTS,CTS pin. So I don't use hardware flow control (HWFC).
The problem is, I...
How do I add a 128-bit UUID?
I am using SDK 14 and see hardly any examples of how to put a 128-bit UUID in my advertisements.
The only relevant example I found is under...
I am trying to package a firmware update and flash it over BLE DFU and I keep getting the following error on the nRF Toolbox app:
"Upload Failed: Unknown Command"
I cannot...
So, I am using the NRF51 as a SPI slave for an RPI3B+. On a l ogic analyzer and O-Scope the Pi is sending its MOSI SPI data perfectly fine. On top of this issue the nrf_drv_spis_buffers_set...
