Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi!
I may have asked about this earlier in a lengthy question:
https://devzone.nordicsemi.com/f/nordic-q-a/35576/low-power-remote-control
But I'd like to be sure about...
(note - my core problem is that I'm trying to compile a file that's larger than 32KB, so I can't use uVision - if there is an easier way to circumvent this then I don't really...
I inherited a Nordic Semi firmware project. It was developed using s132_nrf52_4.0.2softdevice.hex and SDK 13.1.0.
How can I download these versions? I would like to start...
I installed the nRF5_SDK_15.1.0 compiled and ran the ble_app_att_mtu-throughput example.
The first run was using the default settings all went as expected. For the second...
Hello Nordic team,
I am working on ble_peripheral example. Initially application binary file size is 100 KB but after adding support of FDS application size increased to...
Hello,
I have read through all the posts I can find on this subject, but none has solved my problem.
- nRF5_SDK_15.1.0
- Example: Segger Embedded Studio Project: twi_master_with_twis_slave_pca10040...
I want to fully understand the use of RTOS in conjunction with the stack. As an example, I took an example ble_app_hrs_freertos (SDK v15.0).
Add a service, for example...
I need to count the pluse number use 51822, the frequency about this pluse is about 0.01Hz to 1Hz and is not fixed, I know use Time1 can achieve this funtion, but the problem...
I wriing softdevice ,aplication and bootloader by nrfprog tool.
But,the device works with the bootloader, not the application.
After writing, it is reset and flag is set...
Hi
I am using fatfs of nRF5_SDK_15.0.0_a53641a. Iam writing a program with keil.
I am trying to save data using SD card now.
By using fatfs example it was possible...
Hello all,
I wanna ask smth related to the use of the nRF52 as a HID keyboard (USB host).
I have already played around with the SDK example ble_app_hids_keyboard and tried...
Hi,
I'm developing a product with the NRF52832.
I have one Blue LED (APA2107LVBC) which is driven directly by a GPIO as shown below :
With a typical Vf of 2.65V, the...
Hi,
I'm trying to implement the following use case:
On the first button push a sensor advertise and bonds with a smartphone. I do it the following way and it works fine...
I tried to configure OTA in my application, but nrf toolbox stucks in "enabling dfu bootloader" and I can see "Starting DFU" showing up really fast, can it be a problem with...
