This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am developing Timeslot program with FreeRTOS. (on nRF51822)
timeslot's signal handler is
timeslot_signal_callback()
...
xQueueSendFromISR(s_timeslot_queue, &cmd, NULL...
BT 5.0 mention that:
Up to 8x the broadcasting message capacity over Bluetooth 4.2, with
support for larger data packets: 31-octet to 255-octet packages.
Do you have...
Hello,
Brand new bluetooth 5 standard allows to create data packets up to 255 octets.
So, does maximum size of advertising data in Nordic devices comaptible to bluetooth...
Hello, when using sd_ble_gatts_hvx(), I keep getting 0x3401 error. I googled it and it appears that it's because I might not have the notification enabled.
But I very much...
OK. Weird question. I know, but that's only because I'm in the middle of a large program that I'm reading, believe me, I had done my fair share of homework and I understand...
I can't seem to get any of the UART examples for the NRF52 to compile on Eclipse. Eclipse is complaining that there are two definitions for uint8_t, one in _stdint.h and another...
Dear developers,
Currently, I am studying the new SDK 12.2. Now, I'm reading flash storage module. It seems very useful.
Just a question: While Persistent Storage module...
So it points to the ACTUAL value of a characteristic. So why do we need that function "ble_hvx_push()" (forgot its name, sorry, but you know what I mean) for? And what's with...
hi dear Engineers!
if I use sd_ble_gattc_primary_services_discover(..) with NULL last parameter , all SERVICES discovered OK:
start_handle=0x0001;
err_code = sd_ble_gattc_primary_services_discover...
We have a device which needs to survive dishwasher conditions. We believe most dishwashers operate up to 71C, but may reach 82C during 'sanitation' phase/drying.
This is...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. Before I add a DFU service to make it switch to bootloader, I have use...
Hello, I'm sending a series of data up to 7 bytes from an android phone, but I can only receive the first 5.
I'm asking what are the list of thing to mind if I were trying...
Hi,
I am trying to initiate Firmware Upgrade using the nRF Connect Mobile Application (also tried using nRF ToolBox).
As described in the below link -
github.com/.....
The footprint of sd_ble_gap_connect() is:
uint32_t, sd_ble_gap_connect(ble_gap_addr_t const *p_peer_addr, ble_gap_scan_params_t const *p_scan_params, ble_gap_conn_params_t...