Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Dear support team,
Can a Thread Boarder Router have Leader role? I have not seen any document which mention about it but all the Thread topology diagram have independent...
Hello,
I am not able to make the FDS work. Here is my setup
NRF51
SDK 12.3
S130 (2.0.1), i.e. s130_nrf51_2.0.1_softdevice.hex
Using peer manager as well...
We've been using bonding on our device for a while and have a lot of experience there, but we are now attempting to add "Just Works" pairing support that is a configuration...
nrf52832.
SDK14.2
Segger ES V3.34a
I am using nrf_drv_saadc_calibrate_offset() and find the next sample immediately after the calibration is erroneous.
There is...
Hi, I would like to use a nRF51 Dongle to connect to BLE devices and retrieve some data.
I already tried my scenario through nRF Connect for Desktop and it works, so I assume...
Hi,
I have a SPI sensor on an nRF51822, developed in mBED. To save battery power, I want to disable SPI while in ble.waitForEvent(). The only reference I could find is an...
Hi, I'm using Master Emulator API 2.1.7 and am having difficulties determining where I should be processing an acknowledge packet being returned from the slave after transmitting...
Hello,
I have been trying to have a central/peripheral device read UUIDs and RSSI values from surrounding peripherals using their advertisements and without actually connecting...
And base the nus service ,each peripheral can send message for cenrtal to other peripheral like mess.
I doubt it is possible because this example is base on the LED Button...
I'm building a smarthome application.
IPv6 over BLE not support mesh topology that is quite inconvenience to extend network. My teacher require me that this application...
I am working on custom programming of nRF52832. I have little experience of Preview DK. I took help of examples in SDK v15 and came across nrf_pwr_mgmt.h header file which...
Hi,
My service (nRF52832, peripheral, SDK14.2) works in a control point / response manner:
Command code is written by central to 'Command' char (F901). On peripheral...
Hey guys,
The project I'm working on utilizes the secure DFU bootloader and buttonless DFU.
To get the application working I had to generate a bootloader-settings file...
Hi
I have a sample nrf51822 non BLE program (based on flashwrite_example) that successfully writes and reads flash (last flash page) in a loop, incrementing the number that...
Regarding DFU upgrade, I have the following questions（sdk14.2）: 1.nrf52832 will be paired and bound after connecting with the mobile phone, then in the sdk_config.h file NRF_DFU_BLE_BUTTONLESS_SUPPORTS_BONDS...
