On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
Hi.
I'm trying to send data through L2CAP from Cypress BLE evaluation board to nrf51822 chip.
It seems that Nordic's API for L2CAP is much simpler than Cypress', but I...
I noticed some suggestions to add Static Passkey.
I have 10040 nrf52832 sdk13.0.0 s132
The server has no IO, so cannot enter passkey from it.
Is there an example...
Hello,
I am working on NUS service S110 8.0 softdevice and SDK 9.0 and added DFU feature for the application.
First, I connected to the device using MCP from PC. It...
Hi all,
I'm trying to use the nRF51822 sniffer to troubleshoot my TI CC2650STK sensortag ble communication and the output is slightly confusing. The problem I am having...
I need to do the following when assembling a device with nrf-52 at the factory.
Add firmware onto device
Add a unique serial number for the device
Print a sticker...
i have added pwm into proximity profile example and now i am able to make beep using buzzer with pwm library.Now i want to make some sort of Tune instead of beep.
Can any...
hi,all
i use ble-sniffer_win_1.0.1_1111_Sniffer.exe,but it note as follow:
and Why sometimes not get the connection of the data? Sometimes it stop 60 CONNECT_REQ...
Hi
I use SD310 and nRF51 in SDK10 and The Ant is set HRM_MSG_PERIOD_1Hz.
I integrate a heart rate module by I2C and the heart rate data is only all I got.
But the Cell...
Hello,
while I already managed to solve a couple of problems regarding a proper handling of the DFU procedure in my previous topic here , there are still 3 problems that...
I was wondering what would be a good block size, and saw this in the documentation:
For example, if a module has a table with 10 entries, and each entry is 64 bytes...
Hi Nordic,
I am now trying to use ANT acknowledged data type in reverse direction (from slave to master), and I have some questions:
When sometimes, ack signal...
Hey, I want to save stuff to flash under the same id and key which should be no problem as shown in the documentation. But when I save it and retrieve the data only the last...
hi,
i am newer here.
i am confused in nrf_gpio_pin_sense_t i.e. NOSENSE, HIGH_SENSE, LOW_SENSE.
where is use of this feature ?
why it is required instead gpio_input...
In my application many nodes (acting as centrals) will start simultaneously, as they have common power supply. I am using s132 SoftDevice (4.0). Is the frequency hoping sequence...
