Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
Hi,
I try to add support of dfu in our appl. In documentation I could not find info about softdevice size which should be provided in start packet. It looks like I should...
Hi,all
SDK:8.1.0 51822
S7 Edge（android V7.0）
i use the sumsung S7 Edge and the oppo R9S connect with my device,nRF Connect is often note:
GATT_CONN_TERMINATE_LOCAL_HOST...
for ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0
The preferred RAM,ROM and UUID COUNT is shown below
FLASH (rx) : ORIGIN = 0x0001B000, LENGTH = 0x25000...
Hi All
I am trying to build hex file using eclipse id on Mac. everything looks ok, as it eclipse build file without any error but its not working on nrf52 dk.
before...
Now I’m using nRF51822 with S130 SoftDevice.
There are two kinds of devices which is just for scan(A) – 20EA and both scan and advertising(B) - 2EA.
I found that B just...
Hi,
My question is similar to this devzone.nordicsemi.com/.../ but I can't get it to work.
I am using SEGGER_RTT_WriteString and sprintf for debugging, but I am not able...
Our mobile app is currently running atop of easyble and nordicble.js/Cordova. This library works great on all Apple devices, however, Bonding with Android devices of various...
We have done a custom PCB believing that we could use P0.0 as analog input. Now we kind of found out that we cannot, and will change the PCB design. Given that we already...
Hi, I am using nrf24l01+ tranceiver in a project I am willing to sell. I use modules with external antenna and without it. I need the CE certification of the module. Where...
I have used NRF52840 and SDK 13.0.0.
When I have used USB or ESB one by one - all is Ok.
But when they are used together - usb driver goes into an infinite loop here:
...
Hello.
I am developing a project on nRF52832 using SDK 13, in which I need to transfer up to 300 bytes of data from iOS device via my dedicated app (in the background) to...
Hi,
I read in the documentation that one can loop a complex playback. The way I understood, one could load a first sequence (say seq1) and a second sequence (say seq2)...
Hi Nordic Team,
i am working on nrg52 to glow a RGB LED with white and Yellow colours. configured the RGB pins to three different Gpio (A2,A3,A4).
for this i am using...
I have an application where I read a IMU at around 60 - 80 hertz.
How should I configure the S132 so I can send my 14 byte string packet with a constant time interval?...
Good evening (at least here...)
I successfully developed an application with Keil on the Rigado EVAL board with the following steps:
nRFgo Studio -> erase all and...
