Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hi,
I am working for the first time with NRF52832 flash data write. I have (ANT + BLE) application and and I basically want to save the data in ROM in order to keep it saved...
Designing a custom pcb, we have a few questions, and maybe you could help a little bit.
On this Nordic design ,before proceeding to layouts :
Can I skip pins 45/46...
So im trying to create a generic library to test any Bluetooth device. So far i can connect to the device but since i dont know what are the services and UUID available im...
Tried Flasher Portable Stand-Alone Mode with J-Flash 6.14 as following:
Create .jflash Project for nRF51822-QFAA
Open Data .Hex File
From J-Flash, select Target...
Hi,
This is obviously not the first question about this, but I still haven't found the answer I need here...
I would like to make a kind of serial to BLE gateway on...
Hello Nordic Community.
I'm having issues trying to control a simple RGB LED circuit with the NRF52. I have set up 2 timers and PWM instances Red and Green on PWM1 and...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
Hello,
After looking for pin mapping for TRACECLK and TRACEDATA[*] for nrf52840 I've seen 3 different mappings:
P0.07, P1.00, P0.11, P0.12, P1.09 in infocenter.nordicsemi...
Hi
I need to send as much data as it is possible in the advertisrment payload. Whem weset the devicename there are other fields that are automatically added to the payload...
I'm having issues executing any Zephyr project on a breadboard connected to a ISP1302. It works fine on the nRF51-DK but anything I try a final hardware nothing happens. Tried...
Hello,
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0...
Hi, Dear Expert:
I am an Electronic Engineer. We used nRF51422 or nRF51822 at our products, but found the products was easily reset when did +/-1KV contact ESD testing...
now I used sample code of radio
change NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_2Mbit << RADIO_MODE_MODE_Pos)；
In transmitter code , I change
while (true...
Story Short: When trying to run the ble_app_uart example on a custom board with a nRF51822QFAAH0 chip, the code faults and resets at the point in tries to call sd_softdevice_enable...
