Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
Hello
i am using the NRF52 EvalBoard and a ADXL362 EvalBoard. I am trying to read every 100ms the FIFO buffer of the ADXL362. Below you can see my register configuration...
I can't get NRF_LOG working with SDK12.3.0.
Using the same main.c and sdk_config.h from SDK12.2 - here NRF_LOG is working well - I get no messages in J-Link RTT Viewer with...
I have made following connection between nordic device and external sound sensor:
VCC--> 5V
GND--> GND
GATE --> Pin 04
ENVELOPE --> A0
I would like to...
Hi all,
Can you give me an estimate about the power consumption required for the update Fw on OTA.
Our product has a solder batteries, so it's important know if in his...
I am using proximity profile using NRF52 DK.When i started measuring power consumption it is not at all coming less than 2mA.
In order to make as low power ,is there any...
Hi all, I am using a nRF52 in PTX mode to request a progress status from another nRF52 in PRX mode every two seconds. The PRX is updating its internal status every 0.25 seconds...
E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzll_ack_payload
Use gzll_ack_payload this routine master-slave why always send and receive...
I'm using the experimental buttonless DFU app in SDK v13 to automatically change a device without buttons to run in DFU mode for an update.
I'd like to automatically reconnect...
hi:
i update app fail using serial ! SD version 8.0.2 . nrfjprog version 9.0.0.
the device page as follow:
APP_START: 0x18000
APP_SIZE: 0x18000
SD_START: 0x1000...
I use SDK9 s130 nRF51 in central mode. When I save 2 devices in my central, all ok.
In a
m_peer_table[index].id_bitmap
i see that value 0xFF changed to 0XFC
But...
I have been following BLE Services, a beginner's tutorial to add a service to my ble_app_template project. But tutorial was written for SDK 11 and I'm using SDK 12 (s130 &...
Hi, i am using this program to send the data captured on 3 sensors from AIN0,1,2 to the mobile nrf toolbox application via BLE UART.
The problem is that when the sampling...
Hi,
I had done OTA DFU update on nrf51 DK Board using SDK11 version.
Now i wish to do same thing with other custom board which is having nrf51822QFAA. For that, my hardware...
How to test Link loss in the proximity profile using Andriod phone.
By using 'nRF connect' andriod app,Here we can only write and read the Link loss Alert Level.By setting...
Hello,
I just went through the release-notes of the S132 and found a passage that the s132_nrf52_4.0.0-1.alpha introduced some new ble-features like f.ex. the role-configuration...
