Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
Hi,
I have ESB example PTX and PRX, I want to calculate throughput and BER. How do I calculate, and Can you please explain entire setup that I can measure for this condition...
Hi,
I have recently discovered a bug that prevents dfu over serial, using the latest nRFgo Studio v1.18.0.9. I am using SDK S110v8 and the dev kit PCA10028. I was having...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
I've taken the example project at nRF51_SDK_8.0.0_5fc2c3a/examples/dfu/bootloader and attempted to build it using gcc. I'm going for a single bank update over BLE. The SDK...
I have just started coding in Timers in nrf51822. Here i am not clear with the Timer part. Can anybody explain me how to use timer with use of Event Scheduler. Here in app_timer_create...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
Hi all,
I've successfully used the examples for:
OTA DFU for nRF51822 in Bluetooth Smart mode.
OTA DFU for nRF24LE01 (2.4 GHz mode only).
But I couldn't...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Dear all,
I am a little confused about erasing data contained in a flash block. In this link the clear example shows that it is possible to clear bytes from a specified...
Dear all,
I have been trying to get the ADC BLE example working, given at github.com/.../nrf51-ADC-examples
I noticed it gave me error with SDK 6.0.0 saying ble_enable_params_t...
I have been working on ANT for a while on battery powered device. Now because cell App is involved in my project. I want to quickly gain some hands on data on BLE power consumption...
Currently, the Bluetooth communication TEST in progress.
I am using the example experimental_ble_app_uart_s110_pca10028
Applications are received by the data nRFUart2...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I am using two nrf24l01+ at two ends & i am able to communicate between both but its a simplex communiacation means I am transmitting nrf code from A end & B end receives...
After programming a panel of 6 modules embedding nRF51822, I would like to send some data in order to test some features. The basic idea is to validate the modules before...
