Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
I am having problems with th Master Control Panel (no response from master emulator). When I search devzone, I see an answer related to this question that says cloed because...
Hi,
I have application where I drive LEDs with shift registers. I need to send 14 bytes via SPI every 200us while I am in BLE connection. Timing should be exact as shift...
Hi,
I have a project where I need to communicate using UART BLE between nRF51822 and a PC (MS Surface Pro 3) with Windows 8.1 and embedded BLE hardware.
I have programmed...
Hi,
I have downloaded nRF51_SDK_7.0.1_1d6e5cb.zip and run nRF51_mdk_6_1_0_installer.msi
Neither zip file nor created Nordic Semiconductor/nrf51/ folders have ewp or icf...
Hi,
I think it's a simple question. I want to connect a micro to communicate with a phone via the nrf8001. I ported everything thanks to the guide that you posted (for...
Can we use the tx_complete.count given with BLE_EVT_TX_COMPLETE as an indication on how many packets were sent out from the last ended connection interval?
thank you
...
I have a custom board utilizing an RF51822aa device. To test connectivity to the board I built blinky_s110_pca10028. Using Keil 5.12 I tried to debug the program simply expecting...
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash Download...
where can I get working sample code of nrf51822 with nrf24l01
including code of nrf51822, and code of nrf24l01, both TX, and RX.
in my application, I need 518 to RX data...
I am working with a university project where need to connect up to 20 wireless sensors together with 1 master, which will be communicating with either a computer or smartphone...
I found a IAR project at dir [nRF51 SDK_v4.4.1.31827\Nordic\nrf51822\Board\nrf6310\ble\ble_app_hrs\iar].
But my IAR ARM IDE(ver 6.60 newest) don't support nRF51822.
Do...
Hello!
I'm working with nRF51822 Development Kit and s110(Ver.7.1.0).
I'd like to confirm the function about LE Link Layer Topology
specified in the Bluetooth specification...
