Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello, I use BLE NUS since one year to service a device. I recently got to SDK13, using SD132.
When I use iOS9 everything is ok. But when I use iOS10, the tx characteristic...
Im on an nRF52832, using the BLE Mesh 0.9.1 alpha release
I've followed the DFU Quickstart guide, and have been able to DFU the app_green_s132.hex, which is the prebuilt...
hi,
i am using NRF52 custom board. i want to provide serial number to each board, which i want to read or write any time using my firmware. if i erase the bord it should...
Hi,
I have a BLE nano v1.5 from RedBear. I want to use s120 SoftDevice developed for the nRF51822 and for what i've read this is not available for programming with mbed...
Hello,
I have migrated from SoftDevice S130 2.0.1 to SoftDevice S132 3.0.0 and found one mismathing in ble_gap_evt_connected_t structure.
There is absent an own_addr...
Hi,
Is it possible to make pairing without the peer/device/bond manager? I am using SDK 12.3 on NRF51 and/or NRF52 and would like to get it to pair with a certain device...
Hi,
I'm using nRF52840 and S140 based on the ble_app_hrs_rscs_relay example. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu...
Within a buttonless DFU application should nrf_dfu_flash or fstorage be used to erase and write to flash?
SDK 13.0.0 - Soft device s132_nrf52_4.0.2_softdevice running on...
These messages below appeared when I built bootloader_dual_bank(sdk11) in the eclipse.
'Building target: bootloader_dual_bank_s130_sdk11.elf'
'Invoking: GNU ARM Cross...
I want to have blinky orange led,
0 mean on, 0x8000 is off, right? and why??
I have no idea what's 0x8000 mean!
so if I want have orange(full-R and half-G), how can...
I'm trying to debug my UWP Central app, which interacts with our device based on nRF52/s132. What I think I'm seeing with my packet sniffer (the nRF51 sniffer, incidentally...
I have set the
advdata.include_ble_device_address = true
in advertising_init function. However, the mac address data is not shown in mobile APP.
Is it due to the fact...
