Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
How can I trasfer 20bytes data per 10ms?
Currently, I set gap_conn_params.min_conn_interval 7.5ms, and use BLE_EVT_TX_COMPLETE to send data. However, Android APP nrf Connect...
[Aim]
I am working on a project where I aimed to Integrate/Develop firmware management system using Contiki running over Nordic NRF52.
[Components]
Contiki running over...
On a nRF52832...
I'm trying to create a DFU package to update an existing SDK 11 SD2.0.0 firmware, to update it to SDK 12 SD + new application + secure bootloader
But the...
Hi
I am using SDK 12.3.0 with softdevice s130 v2. When I try to combine ble_app_hrs_peripheral code with app_uart.c, uart module gives error NRF_DRV_UART_EVT_ERROR in uart_irq_handler...
I would like to use twenty concurrent connections. As I understand I should set ble_cfg.gap_cfg.role_count_cfg.periph_role_count = 20 and ble_cfg.conn_cfg.params.gap_conn_cfg...
Hello,
I have read with a lot of interest the documentation associated to the "multiprotocol support" associated to the nRF5 SDK for Thread v0.10.0.
As far as I understood...
This is a more specific counterpart to a question I posted on StackExchange . If you want to know more about the attack itself, check that out, but here, I'm asking for a...
Hello, please refer to the below code, in particular, did I get the cccd handle right?
static uint32_t mesh_value_char_add(void)
{
/* BLE GATT metadata */
ble_gatts_attr_md_t...
In order to prevent communication from middle-man attack, I append the signature after ECDH publickey. However, though I get the correct share secret by ECDH, I fail in verifying...
Hi,
I'm using the bluetooth 5.0 and base on the mutilink_center example to add a peripheral and a center. Because I want the center to connect two type device. It could...
Hello,
I have two identical devices with Laird's BL600 chip (that uses NRF51822). They are initialized as NRF_GZLL_MODE_DEVICE and use GZP library (without encryption ...
Hi,
I am trying to write my own bootloader. I gather new image via serial and store it in flash in my application at 0x30000 then invoke reset and in bootloader I want...
Hi,
I was testing the pwr_mgmt project in the nRF5_SDK_13.0.0 with my 52DK, the system off mode seems work fine ,cause the log information is right,but the question is...
