Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi
I did a bunch of boards for a product, and in the latest version I used a BQ25121 PMIC which also has a reset output which I tied to the nRF52 input. On the previous...
Hi all,
There are lots of posts on the devzone about adding DFU service to a custom application and they have been very helpful in getting to this point.
At this point...
I was looking into changing the S130 attribute table size, which is by default set to BLE_GATTS_ATTR_TAB_SIZE_DEFAULT, and noticed that this default seems to be set to zero...
Hi,
I have programmed my nRF52 DK using the ble_app_beacon example from SDK 14 along with S132 V5. I have set NON_CONNECTABLE_ADV_INTERVAL to 3000. I was expecting to see...
Greetings,
I am interfacing AT24C01A(EEPROM) with nRF52 ,SDK11,PCA10040.
For writing to the EEPROM and reading data fromn EEPROM, I am using the following code,
I have...
Hi, when reading the BLE Mesh example code, I got really bewildered by this function:
access_model_add
and inside, there is this gem:
element_has_model_id
...
What's the expected behavior when reading a register that is write only? For example, I'm using an some code that is reading the value of the TASK_START register of the RNG...
Will the Bluetooth low energy advertising tutorial run on 2 x nRF52 DK's and not on 1 x nRF52 DK and 1 x nRF51 Dongle? I wish to test the capabilities of BLE 5.0 (not be limited...
Hello
I'm a beginner using NRF51882, I do not have enough money to buy NDK51 Development or NRF Dongle, the solution I changed STLINK STM32 to JLINK by following tutorial...
Hello,
when starting a new project I took the nice Heart-Rate-Example which works fine at my PCA10040. Then I started to add services and characteristics by copying and adapting...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Can the SoftDeivce flash functions ( sd_flash_write specifically ) be used after the SoftDevice has been disabled? If so will the events still be sent to the handler or will...
each time my program start, I get the error m_evt_schedule_func error 4
what's the cause of this error? is it because I spend lot of time on the handler??? the handler...
