Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
I'm using nRF52832 and nRF52840 to work with MCU, then we should do the firmware update by the uart. I have compiled the bootloader_secure_serial project in the SDK...
I have ordered two "nRF51822 Bluetooth Smart Beacon Kit"s on this page:
www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit , and got these two:
I've downloaded...
Am building a HID Mouse device, starting with the nRF52-DK as hardware target and the BLE peripheral HID mouse sample app. Builds, loads and runs, apparently fine (i.e., can...
Hello,
I am trying to add an extra service like "experimental_ble_app_blinky" into "ble_app_hids_keyboard" example code. "ble_app_hids_keyboard" example code has 3 servcies...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
i am using uart of nrf52832. the SDK is nRF5_SDK_12.3.0_d7731ad. the uart is app_uart .when i was testing the uart sending and receing .i find that the uart is stoping where...
Hello!
We are performing certification testing for our product. We have nRF52832 chip on the board. We used "radio test" example to perform the test and almost all worked...
I'm migrating from sdk13 to sdk14 with work app.
Can't solve one weird problem. When my app start first time I initialize some data with saving by fds library to flash. There...
Hi
I get the following error when i compiled the ssd1306 library from link text to my nrf51DK..
error is: ._build\nrf51422_xxac.axf: Error: L6200E: Symbol app_error_handler...
In the nRF52 datasheets there is a statement:
"The 64 MHz crystal oscillator (HFXO) is controlled by a 32 MHz external crystal"
Is the crystal somehow oscillating at 2nd...
I am trying to compile the blinky example in the SDK 14.
I am getting this error:
makefile:111: ../../../../../../components/toolchain/gcc/Makefile.common: No such file...
I need an application that always advertise the beacon information, such as RSSI and Major and Minor value. At the same time I would like to transmit HID keyboard code. Is...
Hi
I have an application where I cannot use the FIFO buffers (HW or SW). Therefore I need an interrupt for each received byte. If I try to use the uart driver (nrf_drv_uart...
I'm trying to program my nrf52832 with an ST-LINK /V2. I can't get both the softdevice and my app on the chip.
Flashing each one seperately works fine but then when I flash...
Hello there,
I'm trying to flash my custom nrf52832 pcbs(untill I get my DKs in the tech tour with a reconfigured stm32 disco board's SWD port with keil uVision using the...
