Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello,
I am trying a IOT SDK example to connect a NRF52840 to a Raspberry Pi 3 via ipv6:
infocenter.nordicsemi.com/index.jsp
I don't use a low energy dongle because...
I've worked on nRF DFU Library on Android where you can easily do OTA DFU. Same with the nRF Connect desktop application. I was wondering if anyone knows any library (preferably...
I'm developing a BLE gateway/scanner for nRF5 Mesh BLE network, my system components are as following:
Raspberry Pi 3 installed with noble nodejs library (as I'm...
Hello,
I am using nRF52832 s132 soft device and i have read accelerometer adc 3 axis value with sample rate of 244us instead of ms. For controlling my device i have send...
log1.pcap Hi, I am developing a peripheral application that can send around 68k of data in the notifications to the central
Notifications are send at the frequency of 284...
I took the ble_app_hrs code and made changes to suit my application (increased number of peripherals, included bonding/pairing, included ble_nus, added code for button, led...
We have problems when connecting to a device running softdevice S132 version 3.0 with a tablet running Android 7.0.
When we use tablet and nRF Connect, we get Error 8 ...
I tried to add ble_nus service to buttonless app (sdk 14).
Keil doen't raise any errors and compiled project, but app is not work actuall in NRF_LOG I can see these messages...
Hello,
I'm confused regarding the nRF82840 matching network found in the datasheet and dev kit. Is the Pi-filter composed of C3-L1-C4 the 50ohm matching network or should...
Hi,
I have a Rigado BDM-300 (nRF52832) on a small custom board.
Using SDK 13.1 with SD132 v4.0.2.
I've taken a template project and adjusted it to my needs. I can get...
Not sure if there is already a worked-out example of converting analog to digital data from AIN0 and then updating a characteristic with that data.
I've worked through...
Hello ,
I am using examples\ble_central\ble_app_uart_c\pca10031\s120 in the SDK 10.00 .
I know that s120 supports up to 8 peripherals. I am using NRF51 Dongle as a Central...
hello everyone:
i use nrf51822QFAC(with 256kb flash and 32kb ram).The project is this "SDK12.3-ANCS\examples\ble_peripheral\ble_app_ancs_c\pca10028\s130\arm5_no_packs"...
