I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
My external application processor UART, every 5 ms @ 19.2 KBPS transmits a byte to UART RCV of NRF8001, which needs to convert this to BLE and then transmit to a cell phone...
Hello All,
I am working on nrf52832 and i designing the custom board for the same for my application , which all pins i need to select as programming pins to dump the code...
I'm trying to figure out why "some" (as in not all of them) Android Devices drop my Bluetooth Low Energy connection (to an NRF52 which I don't think is the problem) after...
I'm trying the example border router using 2 x nRF52840 boards one with CLI and the other with NCP connected to a PI. I can get ipv6 addresses and get them to ping each other...
Hi, I am trying to control an Omnivision Camera module using the nRF51822 EK. The module uses their proprietary SCCB protocol, which is very similar to I2C. However, there...
I am now using 52832 to do a project, need to send a BLE broadcast package first, and then start scan, what examples can I refer to?
Attachment is my TX/RX process，and...
Hello,
I always observe 4.0xxV from the li-po battery attached after when thingy52 stopped charging.
I think this problem maybe because of output current from the battery...
On our project we're using a Raspberry Pi 3 compute module with custom hardware and 2x nRF51 SoC running HCI from Zephyr.
We'll be delivering more than 150 of those devices...
Hello! Can I use one of the gpio pin as power source directly for other MC on my board (hx711 - ADC with current consumption in normal mode 1.5ma (from datasheet)). I understand...
Hello, long story short:
You now must use write request instead of write to write the CCCD descriptor.
Allegedly (according to a nordic employee) both types...
Hello,
We are currently designing the hardware for a production run of our product using the nrf52832 chip and would still like to have debugging capabilities with breakpoints...
I'm using an NRF51822 with soft device s110 version 7.1.0 and I'm having timer-related issues.
I create 1 periodic timer and 6 non-periodic (single shot) timers with app_timer_create...
Hello guys,
Hope someone can help me here. I am working with the NRF52 and want to use Zephyr . I am able to flash it. Using the nrf52 as periphal does not cause problems...
