Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi , I have 2 nrf51822 borads. One is with nRF5_SDK_12.3.0_d7731ad\examples\ble_central\ble_app_hrs_c and the other is with nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral...
I would like to use the ble_app_uart_c example, found here , to connect to a custom peripheral. What values should I change in the central device code in order to connect...
I know that BLE is not suitable for high-volume streaming.
So how do BLE earphones stream audio?
Does it use with bluetooth classic protocol?
And I coundn't monitor...
Hi,
I've one central and one peripheral devices. I'm trying to make a connection between them, perform a bonding process and finally add the peripheral id in the whitelist...
Hello All
I am developing BLE based home automation system using nRF51422 DK for my research activities. now i am planing to make separate PCB nRF51422 device alone. i...
Hi,
I'm trying to get the RSSI of incoming 802.15.4 packets using otLinkRawGetRssi() , but I need only RSSI from one specific device. I tried to use whitelist ( otLinkSetWhitelistEnabled...
Hi, I ran the example code ble_hrs_c in nrf51822 16KB RAM version and 32KB RAM version. The 16KB RAM version works fine. But in the 32 KB RAM version, peer_manager_init(true...
I modified the HTS app in the nRF toolbox to test adding other services like below.
In detail, I added mDICharacteristic field to save the information of System ID...
Hello,
I developed a Nordic board with 2450AT18B100 chipset antenna. I follow the design of Solar Powered Sensor Beacon.
infocenter.nordicsemi.com/index.jsp
I test...
Hi, I'm building a product with use this kit www.nordicsemi.com/.../nRF52-DK and I would like of know how write the firmware in others CIs to can use in my circuit board....
Hello,
I am currently working on project that uses BLE peripheral and BLE central for automatic sensor calibration on custom board. There is an initial connection where...
Helllo All,
I designed on custom board (nrf51822 and used 4 programming pins(swck,swi,gnd,vcc) but how to program/flash the soc?which segger i need to purchase?
Hi There,
I am
Using Linux as host platform
I'm able to successfully compile and download the example to the nrf52dk.
But I didn't understand how to debug the example...
I'd like to get peer address after the connection between nRF52 and other 6lowpan device is established. This address will be then used to create a TCP connection with some...
Hi All,
I am using the Nordic nRF52 nrf52832 device to read a value in from an Android device. The value will be between 5 and 60 seconds. I'm using the experimental_ble_app_blinky...
