Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi all,
I am a bit confused about the use of SOFTDEVICE_HANDLER_APPSH_INIT and similarly APP_TIMER_APPSH_INIT. I've not been able to find anything in the documentation...
nrf52840, S140.
So for the past 1 or 2 weeks I have been fighting with this problem :
Now it turned out that the connection handle may actually be INVALID, it's 0! ...
I am using nRF52840 DK as a SPI slave with an external MCU configured as SPI master. The SPI clock frequency is set to 1 MHz. I am using the following pins for SPI:
P0...
Hi All,
I have just got my nRF51 kit (S130) and started working on a beacon project which would transmit advertisements packets from peripherals over a RS485 to a server...
Hi,
im running my DK as a central of a BLE connection and i'd like to read the device_name of the peripheral board that im communication with. how do i do this? i cannot...
Testing on nrf52DK (QFAAB0), without softdevice, unfortunately still on SDK10 and
NRF52 sleeping on RTC. Programming pins disconnected.
Measured:
low frequency clock...
i am total beginner to the nrf51822. i am going through the nan-36_v1
app note is using s110 but i can't find that soft device in sdk ? is there any changes has to be done...
Hi,
I took the ble_hrs_c code and modified it such that it has the NUS service and can connect to 2 peripherals. The code works when I power cycle the central+2peripheral...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
Hi guys,
i'm trying experimental_ble_app_queued_writes out. I have some strange behavior.
The qwr service is
6e400001-b5a3-f393-e0a9-e50e24dcca9e but the characteristic...
I am developping NUS server(Peripheral) on Android. Central is ble_app_uart_c on nRF52832.
In this case, service discovery cannot be completed.
According to the console...
Hi. I am new with KEIL MDK and Nordic and ARM .....
I will create an MIDI BLE, but maybe anybody has an working Example for this?
Or what for an Example i can modify?
...
Hello, when I try to compile old working projects in SDK 11.0 with both Device Family Pack 8.5.0 and 8.11.1 (which I am using for SDK 13), I am running into the following...
