Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello,
I am working on NUS service S110 8.0 softdevice and SDK 9.0 and added DFU feature for the application.
First, I connected to the device using MCP from PC. It...
Hi all,
I'm trying to use the nRF51822 sniffer to troubleshoot my TI CC2650STK sensortag ble communication and the output is slightly confusing. The problem I am having...
I need to do the following when assembling a device with nrf-52 at the factory.
Add firmware onto device
Add a unique serial number for the device
Print a sticker...
i have added pwm into proximity profile example and now i am able to make beep using buzzer with pwm library.Now i want to make some sort of Tune instead of beep.
Can any...
hi,all
i use ble-sniffer_win_1.0.1_1111_Sniffer.exe,but it note as follow:
and Why sometimes not get the connection of the data? Sometimes it stop 60 CONNECT_REQ...
Hi
I use SD310 and nRF51 in SDK10 and The Ant is set HRM_MSG_PERIOD_1Hz.
I integrate a heart rate module by I2C and the heart rate data is only all I got.
But the Cell...
Hello,
while I already managed to solve a couple of problems regarding a proper handling of the DFU procedure in my previous topic here , there are still 3 problems that...
I was wondering what would be a good block size, and saw this in the documentation:
For example, if a module has a table with 10 entries, and each entry is 64 bytes...
Hi Nordic,
I am now trying to use ANT acknowledged data type in reverse direction (from slave to master), and I have some questions:
When sometimes, ack signal...
Hey, I want to save stuff to flash under the same id and key which should be no problem as shown in the documentation. But when I save it and retrieve the data only the last...
hi,
i am newer here.
i am confused in nrf_gpio_pin_sense_t i.e. NOSENSE, HIGH_SENSE, LOW_SENSE.
where is use of this feature ?
why it is required instead gpio_input...
In my application many nodes (acting as centrals) will start simultaneously, as they have common power supply. I am using s132 SoftDevice (4.0). Is the frequency hoping sequence...
Hi experts,
Can we add capacitor to the swdio pin to improve ESD capacity?
We have make some sample that add 1uF capacitor to the swdio, indeed have improved the ESD capacity...
hello there i want to use c++ library in nrf51dk project. i am using sdk12.
i change main.c to main.cpp
but i am getting error. uart_original.rar
i have uploaded code...
