I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi Everyone,
I am trying to record data from ADC to a SD card every 500ms using nrf52832.
I am following the fatfs example. Before I had a problem whereby every approximately...
What are the most recent set of software tools that are known to work on OSX Sierra?
Any pointers to a good IDE for debugging will be great. I understand there are many questions...
Hello there,
I'm trying to learn how to use some of the perepherials of the nrf52832 with the DK,
trying to learn a little about the SAADC I found some example modified...
Thank you for reading my question.
peripheral project :ble_app_hrs_rscs_relay，SDK14.1 ,S132
client project: another manufacturer's soc
I set peripheral peer manager...
Hi,
I am testing with ble_app_uart . my board will advertising to my phone . I realize that if I don't connect 2 pin uart on NRF board to USB TO COM to my PC . Then , my...
Hi,
Are there any examples of SDK examples that work with USB BULK communication?
Which example should I use to make usbd_hid_generic example work with BULK communication...
Hello,
We are using Nordic SDK 11 MQTT adapted for TCP/IPv4(separate module) . It works fine without TLS. I added the flag "MQTT_TRANSPORT_SECURE" and made adaptations...
Hello,
Question regarding using the SPI master peripheral with DMA to communicate from the nRF52832 to the ads1296 device .
In order to use this device in the mode and...
Hi engineers, Here we are facing a critical problem in which the NRF51822 stops handling/processing the GPIOTE->PORT interrupts after some days good working. This problem...
I have a project which needs to be built in IAR, but uses the signed bootloader. I understand, that if I want to flash and debug the application from within IAR, I need to...
Hello,
In my next project I plan to conductive pads as buttons(that are exposed for humen touch to interacte with the) one is connected to ground and the rest will connect...
Hi,
I am using SDK v14.1 for nRF52840.
The secure_dfu_usb debug example works well when the J-link RTT Viewer is connected.
But when the RTT Viewer is disconnected the...
Hi everyone,
I would like to know if it is possible to establish a serial communication to a PCA10028 card using Adafruit Bluefruilt LE friend knowing that there is no...
Hello everyone,
I am using nrf51822 chip that has functionality to flash bl, sd or app using mobile app application. I want to reuse this functionality in order to have...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
