Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
We use IOS DFU toolbox to upgrade firmware with BLE device. we can upgrade successfully with Android, but always failed with IOS.
wrong code is: DFUErrorReadingVersionFailed...
Hi, it's probably a very dumb question, but i don't seem to find any details about it. In nrf52 SDK documentation, in Error Module section it says
The behavior of the...
Hi friends...!
I want to put dynamically changing MPU data into the advertising packet. I am putting my accelerometer data into manufacturer specific data field of ble_advdata_t...
How robust is the output PA of the nrf905?
Assume the ouput matching network and 50Ohm connector is used as in the 868Mhz application note.
If the antenna is removed...
Hi,
I'm trying to find a way to speedup the upload procedure of an application, via BLE on a Arduino Primo with the DFU service.
Here you can find my code:
https://github...
Hi,
I am using ble_app_uart sample code for testing. In that I want to store the incoming data into to three buffers and simultaneously sending this over BLE. i.e., consider...
hi i m using nrf52832 for detection acceleration , angular speed and detection of magetic field with GY-87 ( MPU 6050 and Hmc5883). in fact i wrote a program that read only...
Hi,
I am using s130v2 and running the example code from: nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_hrs\pca10028\s130\arm4
This is the only modification I...
Hi,
I know this is a Bluetooth 5 spec question, but wanted to know the practical figures for current consumption when nrf52840 is used as both central and peripheral...
Hi,
We are expecting many of our devices to be in close proximity. How can we be certain that when a user initiates a buttonless DFU, that they are uploading to the correct...
Hi,
I thought central is the one which fills up its look up table with 16 bit IDs to keep track of the peripherals. If multiple devices can act as central at the same time...
I am trying to re-base my SDK package, and when I started off with the ble_app_template project for the pca10040 s132, I copied my main file on top, everything compiles just...
I am developing an application which involves control of a brushed DC motor with a quadrature encoder. According to this post, in SDK 12.2.0 - which I am using - it is possible...
Hi,
I had a problem with my NRF52 chips. I'm using one BL652 (Laird) with SoftDevice s132 (4.0.2) and a standalone nRF52832 also with the same SoftDevice. I was trying...
