We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello, I can program properly (the "--verify" command passed) my softdevice s140 into the chip, using nrfjprog 9.x. But now I can't use my keil uv5 to program my user app...
Good morning,
Based on different articles, I set up a nrf52832 with S132 3.1.0, the secure bootloader found in "SDK_12.2.0/examples/dfu/bootloader_secure" and the buttonless...
Hi together,
I'm using nrf52832, SDK 12.1.0 and S132 3.1.0.
I integrated the peer manager to my application code and have the following questions concerning the bonding...
Hi,
I noticed a possible issue in BSP_MS_TO_TICK macro computation.
In bsp.c, the macro is defined as:
#define BSP_MS_TO_TICK(MS) (m_app_ticks_per_100ms * (MS / 100...
Hi nordic,
Is there any ways to implement that my device connect with one special Central Device likes Andriod phone and Iphone. Currently I know is whitelist. First I add...
Hi;
Is it necessary to reset SoftDevice when using NVIC_SystemReset ()?
The SoftDevice must only be initialized if a chip reset has occured.
I saw the above comments...
Here is the code I'm using to test it out:
static float number = 0.5678905;
NRF_LOG_INFO("Float number: "NRF_LOG_FLOAT_MARKER"\n\r", NRF_LOG_FLOAT(number));
And...
Hello,
I am working on NRF52382 custom board, where I am running a timer of 30 sec to get a value every 30 sec.
I want to save this value in flash.I am well aware of...
Does the s210 softdevice not function on the nRF51822? I see it available for the nRF51422 here but it is listed under the 51422 only.
I have a v1.1.0 PCA10031 (nrf51422...
Hello,
I developed an application for the nrf51822 Smart Beacon, SDK11 s130, that basically advertises the battery lvl of the beacon, the staus of button_1 and the number...
I have a nRF 52 DK board. I have flashed dtm example onto it. I have connected a USB to serial UART interfacing board ( www.sparkfun.com/.../12731) to the respective Tx, Rx...
Both the capacitive touch library and the driver (which is better ?) are using the analog inputs.
There are only 8 of them , and we need 10 at least buttons.
Is there...
I'm migrating from SDK11 to SDK13. My custom service is based off Heart Rate Service, so I started from the new SDK13 example of HRS, and updated all the initialization code...
