Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
nRF5 SDK v13.0.0
Release Date: Week 11, 2017
Highlights:
Implemented a new license scheme for the SDK distribution. See the
documentation folder for details....
Hi,
I am using "nrf5 sdk v11.0" ble_peripheral "ble_ancs_c" example for nrf52_DK(PCA10040) .
When i connect to the my ios device then accepted pairing request then i am...
is it possible configure the QDEC to single phase, i am using one omnipolar hall effect sensor i am wondering if i can configure only phase A ande use it, is it possible ...
Hi, I wonder why my pwm uses so much power in WFI mode. It uses around 470uA and when I do not use pwm that current is around 1.8uA. I tried to disable pwm but without success...
if i am not wrong the connections i found is as i shown in the image..
the module doesn't show up in my ide tool (keil ) although my kit works fine but i need it for standalone...
Dear Nordic Team,
I am work DFU with ble_app_uart example , as per the info center document : infocenter.nordicsemi.com/index.jsp and also followed by the example for ble_app_hrs...
when use the sd_ble_gatts_hvx() send data and printf() the value below
p_ble_evt->evt.gatts_evt.params.hvc.handle
p_ble_evt->evt.gatts_evt.params.sys_attr_missing.hint...
how to save a problem,if one Thread use sd_ble_gatts_hvx() send many package ,but i use vTaskDelay(50)( the freertos delay api ) when one package send ,then send another package...
ru.txt ra.txt Can someone help out in this. There is no option to capture the data in RTT. Somehow I am not able to take a screenshot directly from the Windows on my MAC.
i to all, I have just bought NRF51 DK from arrow.com I couldn't found one in Turkey. I am not new to C programming but I'm new to ARM architecture. I will be brief. I want...
Hi,
I wrote an application based on ATT_MTU Throughput Example. Now I'd like to add support for Thread protocol. Is there a possibility for adding OpenThread libraries to...
Hi to all, I have just bought NRF51 DK from arrow.com I couldn't found one in Turkey. I am not new to C programming but I'm new to ARM architecture. I will be brief. I want...
Hi,
I use sdk 12.2 for my production software with UART protocol, my product is distributed to customers since 6 months with many type of phone or tablets using it without...
I have inherited a project where the Makefile sets __HEAP_SIZE and __STACK_SIZE for both CFLAGS and ASMFLAGS:
CFLAGS += -D__STACK_SIZE=2048
CFLAGS += -D__HEAP_SIZE=0
...
