Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I thought central is the one which fills up its look up table with 16 bit IDs to keep track of the peripherals. If multiple devices can act as central at the same time...
I am trying to re-base my SDK package, and when I started off with the ble_app_template project for the pca10040 s132, I copied my main file on top, everything compiles just...
I am developing an application which involves control of a brushed DC motor with a quadrature encoder. According to this post, in SDK 12.2.0 - which I am using - it is possible...
Hi,
I had a problem with my NRF52 chips. I'm using one BL652 (Laird) with SoftDevice s132 (4.0.2) and a standalone nRF52832 also with the same SoftDevice. I was trying...
hi guys. i'm have a project with nrf52832.
i use jlink v8 debuger clone form china, just 12$ and have this troulbe in this figure
Untitled.png
could you help me?. jlink...
Hi,
I was trying to write the s132 SoftDevice from the nRF5_SDK_13.0.0 onto the Sparkfun nRF52832 breakout via OpenOCD and an ST-Link v2 debugger. The SoftDevice flashed...
Greetings -
I am working on a peripheral-heavy project. Many of the devices seem to work Just Fine with VDDio of 1.8 volts. On device seems to be having fits and I need...
void Gzll_TxSuccessCallback(uint32_t pipe)
void Gzll_TxFailedCallback(uint32_t pipe)
More than two functions are not accurate judgment
GZLL agreement return function cannot...
I try to implement this library to my code.
uint32_t settings_set_erase_flag(int32_t flag)
{
uint32_t err_code = fds_write(flag, ERASE_BOND_FLAG);
return err_code;...
Hello I have this error:
Checking installed packages
pyside: 1.2.4
pyqtgraph: 0.10.0
numpy: 1.12.1
pynrfjprog: 9.0.0
Warning: The software is tested with PyQtGraph...
I wrote a peripheral similar to NUS. Then I use the multilink central to connect to 3 of them. First two are fine. But when the 3rd is added, the 3rd one would connect, but...
Hi,
I want to make an BLE_UART dongle which will receive the data from the module(An external module is connected through UART) and it will be send over the BLE to ble_receiver...
I'd like to write some timestamps to a log variable in order to see how much time has elapsed between certain points in my code. app_timer.h has two functions that look suitable...
Hello,
I have a problem while combining peripheral examples in SDK13. I am trying to combine twi_sensor and uart but when I do this in uart folder, compiler gives following...
Hi support team,
We met an issue for connecting our device built in nRF51822 to Android device.
The nRF51822 uses below firmware program:
nRF5_SDK_12.3.0_d7731ad...
