Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I wrote my own nRF24L01+ library for my AVR AtMega2560. I used the datasheet and the widely used Mirf library as my guide. I am happy to say I got it working. I have...
I have a new PC (running 64 bit Windows 7) and am having issues after install nrfgo studio. I had it running previously on another windows 7 (64 bit) machine with no issues...
I noticed that there can be three SPI instances (SPI0, SPI1, SPI2) for the nRF52. Is it possible to have three TWI instances? We have a sensor network that requires 6 of the...
i have used 52832 for pdm clock generater, but i just can set the frequecy to fixed such as 1.032 MHz,1.067 MHz.., if i want to set the frequecy to 1.050MHz, i can't come...
Hi,
I am trying to run LWM2M support based on Contiki OS (contiki/examples/ipso-objects) on a NRF52 (PCA10040) development board. I can successfully build (make TARGET...
I see Nordic release pc-ble-driver 2.0.0 some time ago. I'm using 1.0.0, before I upgrade to the new version, I'd like to know what's new in it....could not find any list...
Hello,
I am using nrf51822 SDK11 S130.
I am using my custom design board which is powered by 12V. The nrf51822 is provided with 3.3V. I used 27k and 9.53K resistors in...
Hi,
I have two nrf52832 boards. One as mater and other as slave. I'm trying to develop a communication between master and slave through ble. Also i need to connect the master...
Hello, can someone tell me how I can change this, as shown in the picture?
Strangely, I have already selected the proper target device, as shown in this pic:
What...
I want to use UART to read GPS data while advertising.
After I add uart function to ble_beacon_example, UART API app_uart_get() always return NRF_ERROR_NOT_FOUND.What can...
Hi,
Can Anyone has experienced with nRF52 PWM clock generation ? I am trying to generate 8-Mhz clock out of GPIO by configuring it for PWM module.. But so far I can get...
I have taken ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0 and i integrated Alert Notification Service,DIS[device information service] and DFU... Device...
I'm using the latest version of Keil with Software Packs. As I understood, copies of configurable files are stored in RTE folder. Non-configurable files are stored inside...
When i connect the board to pc its not detected and No J-link device in device manager
But when i press and hold the IF BOOT/RESET button and power cycle the board the LED5...
