Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello:
Im rewritting a program from ST32F105RC to NRF51822.
In a part of the program of ST32, it checks if the interruption from pins 5-9 (EXTI9_5_IRQn) is enabled, and...
Hi,
I worked with temp sensor example and sofdevice s110 and something stuck on some function.
Anyway, I made readout from registers but softdevice blocks register access...
My nRF51 will occasionally lose connection to the computer, and I have to disconnect and then reconnect it before it will work. How can I reset the device dynamically, without...
I'm trying to compile a project I have for nrf51 on nrf52. I am running into errors with macros not being set.
For example:
error: #20: identifier "ADC_CONFIG_RES_10bit...
Hi,
I'm working on a sensor application that sends out fairly large quantities of data via BLE notifications. I understand how bluetooth works and have read and followed...
Hi,
I'm currently testing ble_app_uart on nRF51822 custom board. I connected it to nrf51 DK P19 and was able to program the hex file successfully.
But it doesn't run...
Hi, In your documentation you specify the maximum CPU temperature 85 DegC.
What problems could one expect after this point?
How much safety margain du you have on this number...
I'be been reading over and over the datasheet but cannot see how to dissable Enhanced ShockBurst features for my application which only requires basic one way radio.
I...
Hello,
I'm trying to program that module, but i can't do it correctly.
I'm using a program that works fine in nrf51 DK, but when I program this in ptr5518 my smartphone...
I want to port either the S210 experimental DFU over ANT_FS to serial DFU or the S110 dual bank serial DFU project to be S210 compatible.
I'm using S210 V4 and SDK 8
...
I would like to connect more than 8 devices to a single host. Therefore I would have to set the same role to multiple devices.
What are the implications of using the same...
HI,
I have some problems with the function sd_ble_gap_scan_stop(). I want to stop scanning into the RTC1 event handler but when I use this function (sd_ble_gap_scan_stop...
HI:
i have a question.if i use 51822 to connect other ble(ti or csr) ,could that be achieved.i have used ti dongle to scan 51822,but can't found 51822 device.if 51822 connect...
Hello,
In our project we use HID service. The difference between our HID and standart HID is that we use our own UUIDs. Our report charactestics include Report Refernces...
