Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hi,
I have tested the nRF Toolbox proximity application using nrf51822 evaluation kit and with nexus4 smartphone it is working fine. Now my question is, is it possible to...
Hi
I am trying to overcome the problem that I have confronted, I have no buttons to delete bonds. So instead of deleteing this is what I did.
I modified the bondmanager...
I am developing hid_mouse . When I connect Android once and ubond hid_mouse I must set bluetooth off and on again to connect ble device otherwise it will connect again to...
Hi,
I am trying to set a value in the NRF_POWER->GPREGRET when softdevice is running, but it doesn't work. I don't get any error, but the value is always 3 and not 1 like...
Hi,
i took the example in AN36 (with the led but deleted the button stuff) and added the Battery Level service. Both are working fine together. On top of that I took the...
I have a development dongle PCA10000 , PCA10001 board and nRF pebble.
My aim is to come up with a project where one of these devices
a) would advertise,
b) the other...
Hi,
It has been mentioned in several threads that the MCP/dongle (on laptop) cannot support transmission of more than 1 packet per connection interval. Could you help clarifying...
/**
* @brief Function for unconfiguring GPIOTE channel.
*
*
* Note that when unconfiguring the channel, the pin is configured as GPIO PIN_CNF configuration.
*
...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I have set up the UART example with PCA10000 and PCA10001. Everything works fine but one strange thing is the time to send 100kB of data. See my times below:
38...
Hi !
On this thread devzone.nordicsemi.com/.../nrf51922-1 i've found someone introducing the new S130 softdevice for the nRF51822 wich allows the IC to be on concurrent...
Hi to all,
Ihave a problem with erasing flash on nRF51422 Evaluation Kit. When i click on Erase all button in nRFGo Studio everything is looking normal ( segger led is blinking...
I cannot download S110 to try right now. I have some 51822 Dev kits, but somehow I didn't get the product keys entered into my page, and the boxes are all gone.:D
