Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I will use ADC / Button function over SoftDevice.
below by source.
the thread is repeated not go beyond the conn_params_init.
#define ADC_SAMPLING_INTERVAL APP_TIMER_TICKS...
Hello,
I am working on s130 softdevice(SDK 6.1.0.0 and nRf51822 &nRf51 DK). I have one peripheral and two centrals. but the data from peripheral should be read from only...
I find this function.
tx
void ble_send(uint8_t * data, uint8_t length)
{
ble_nus_send_string(&m_nus, data,length);
}
ble_send(&data_array[0],10);
but I don...
Hi, I'm trying to run ESB during the timeslot api requested slots.
The problem is that BLE uses app_timer, which uses SWI0 for the callbacks, and at the same time, ESB also...
Hey , I am working on nordic nRF51822 chip and using it as an iBeacon. I want to send some custom data apart from UUID,major,minor in the packet. How can I send it ?
As in...
When I try to set a breakpoint in eclipse by clicking on a line, gdb tells me in the eclipse "Console" window below the code: "No symbol table is loaded. Use the "file" command...
Hello,
I have three custom services. I wanted to add descriptions to the characteristics for easier testing and debug, so I used the typical method to add descriptions...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi
I'm trying to test UART over BLE using the nRF51-DK and the sample code "ble_app_uart_s110_pca10028 (nRF51 PCA10028)" along with both the nRF UART APP for both Android...
I'm using nRF51822 SoC , is it possible to change the major value when i push the button ? I tried simple assignment but it didn't work so i ask if i have to use the function...
hi,
i have kept RAM block 0 and RAM block 1 on in OFF mode by calling "sd_power_ramon_set(0xf000f)" before entering off mode ,i saw the value of RAMON register is 0x00030003...
I'm using nRF51822 SoC . I wanna read and write from the flash memory . Shall I use a specific configuration before using read and write functions provided from S110 softDevice...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED??
please someone...
