Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
I have initialized SPI0 master by this code:
static const nrf_drv_spi_t spi = NRF_DRV_SPI_INSTANCE(0);
...
nrf_drv_spi_config_t spi_config = NRF_DRV_SPI_DEFAULT_CONFIG;...
Recently I have been working with the serial bootloader from SDK 11. I can upload a softdevice, and supporting application using this bootloader without issue, as long as...
I started working on mesh 51 series ,
Points for which we need inputs
Data packet size for transmission
Process for association and address assigning during commissioning...
Hi,everyone
I am using S132 and SDK13 to set two peripheral links,now i want connect two centers using different connection parameters at the same time,for example,connect...
Hi,
Can the nRF52832 support higher data rates:
UART TX baud rate of more than 1Mbps, such as 3 Mbps without bitbanging.
TWI of 1MHz
any trick to get them...
Hi,
I recently purchased the NRF52 DK. I'm using the ble_uart_example for the SDK 11. I'm using the softdevice PCA10040.
I noticed the the SDK 11 includes the RTT c...
I want to use the nrf52840 with DCDC in high voltage mode to drive the circuite directly from a LI-ION battery.
Is there any reverse current protection built into the chip...
When you start a receive task, what will the radio do if the HFXO is not stable? Not begin to ramp up until the HFXO is stable, OR begin to ramp up but not become active until...
nrf52832, returns an error even with parameters
IROM1: 29000 57000, IRAM1 3CC8 C338, softdevice_enable() works without errors.
#define PERIPHERAL_LINK_COUNT 1
#define...
im working on nrf51822 using sdk 9 ....i completed bonding using ble proximity example without privacy key.....now i wish to add privacy key ..what all changes i have to make...
I'm using the with SDK version 13.1.0 along with S140 SoftDevice v 5.0.0-3.alpha and trying to utilize the Bluetooth 5 Extended Advertising feature.
The function ble_advdata_set...
I'm periodically polling a TWI sensor with a blocking call, as in
ret_code_t err_code;
m_xfer_done = false;
err_code = nrf_drv_twi_tx(&i2c, address, subAddress, 1,...
My external application processor UART, every 5 ms @ 19.2 KBPS transmits a byte to UART RCV of NRF8001, which needs to convert this to BLE and then transmit to a cell phone...
Hello All,
I am working on nrf52832 and i designing the custom board for the same for my application , which all pins i need to select as programming pins to dump the code...
