Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi All,
I have just got my nRF51 kit (S130) and started working on a beacon project which would transmit advertisements packets from peripherals over a RS485 to a server...
Hi,
im running my DK as a central of a BLE connection and i'd like to read the device_name of the peripheral board that im communication with. how do i do this? i cannot...
Testing on nrf52DK (QFAAB0), without softdevice, unfortunately still on SDK10 and
NRF52 sleeping on RTC. Programming pins disconnected.
Measured:
low frequency clock...
i am total beginner to the nrf51822. i am going through the nan-36_v1
app note is using s110 but i can't find that soft device in sdk ? is there any changes has to be done...
Hi,
I took the ble_hrs_c code and modified it such that it has the NUS service and can connect to 2 peripherals. The code works when I power cycle the central+2peripheral...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
Hi guys,
i'm trying experimental_ble_app_queued_writes out. I have some strange behavior.
The qwr service is
6e400001-b5a3-f393-e0a9-e50e24dcca9e but the characteristic...
I am developping NUS server(Peripheral) on Android. Central is ble_app_uart_c on nRF52832.
In this case, service discovery cannot be completed.
According to the console...
Hi. I am new with KEIL MDK and Nordic and ARM .....
I will create an MIDI BLE, but maybe anybody has an working Example for this?
Or what for an Example i can modify?
...
Hello, when I try to compile old working projects in SDK 11.0 with both Device Family Pack 8.5.0 and 8.11.1 (which I am using for SDK 13), I am running into the following...
Hello,
some time ago I was struggling with interfacing an I2S microphone with the nRF52832. That remained unsuccessful. My conclusion back then was that the selected I2S...
Hello, i use ibeacon example, this is the reader advertising packet, he has 31 byte long:
0201041AFF590002150112233445566778899AABBCCDDEEFAB010200FFC300
in this packet...
(/attachment/fad3a1e781331c528a9db48ec177b9b7)Hi there! i need help. I am using NRF52Dk with Bluetooth developmebt studio.
I set up my custom service in BDS an then imported...
