I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello,
I'm using a nRF51822 to send data to the iPhone using the NUS service. I'm using the oldest SDK4.x and v5.x S110 soft device. I know that the least connection interval...
Good day.
I`m very new to nordic chips.
I`m try to use NRF52832 as TWI master with OLED display based on SSD1306 with I2C.
And got this.
Yellow is SCL, Blue...
Hi,
I am trying to use the FDS for saving some variables and displaying them again later. I have downloaded the NRF52-fds-master sample code posted on github. However,...
i am working with mpu xx example given in nordic website. it seems code is working fine i.e. compiling and dumping into nrf52 DK, But not showing any output values.
i was...
I am using an Nrf51822 for a project. I looked in the datasheet and it said that there is a built in WDT for the chip. It also says that clocks can't be used while in systems...
I want to use in my project tft 1.8 display with st7735 controller. I'd like to use some based code but can find nothing except on infocenter nordic
As I understand there...
Hi,
I am writing a boot loader which does not need to use the soft device as the image is being transferred over an SPI interface.
I have merged the softdevice and my...
Hi
I suppose that Multiple connection to centrals is available from BT4.1.
Is it possible to realize bu S110?
If it is so, which version is available the specification...
Hello, I made some boards on nrf52832 and I was testing the PCB.
The test program is ..\nRF5_SDK_12.0.0_12f24da\examples\ble_peripheral\ble_app_hrs.
(I have downloaded...
Hello! Just got a few NRF51822's.. looking to just brodcast a few basic URL's.. if someone can point me in the right direction or maybe let me know where I can hire someone...
I work with ble_app_uart example and want to move uart init and event handler into separate file( e.g uart.c).
I just copy uart_init, uart_event_handler functions with some...
I am writing code that runs on a NRF51822 (to be less specific it runs on a Red Bear Lab BLE Nano). The board has a 32.768khz crystal on it that I want to use to wake up the...
Now I am sending data at 250 ms.
I'd like to send data at 80 ms.
Is this possible?
also,how much can it extend the advertisement interval to the maximum?
thank you in...
i am working with eclipse to program the ble_app_hrs but it is getting error "No rule to make target _build/app_trace.o', needed by nrf52832_xxaa_s132'. Stop" when it builds...
Hi,
In the newer versions of NRF 5 SDK (sdk10 vs sdk12), does the softdevice takes more RAM?
I am using nrf51822 (qfaa) and sdk 12.3. with softdevice s130_2.0.0.1....
