I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
In the "nRF52840 Preview Development Kit v0.9.x" document, I see some power numbers listed for a run mode.
However, I am also interested in the following power numbers...
Hi,
i am using Nrf52 DK board and
i am working on TWI to get accelerometer(MMA7660) values using TWI driver. so that i am getting accelerometer values and Tap information...
Hi guys,
I bought the sparkfun breakkout board ( www.sparkfun.com/.../13990) . I also have the NRF52 DK from Nordic. I programmed the breakout board via the DK over SWD...
Hello All
softdevice version "s130_nrf51_2.0.1_API"
sdk version "nRF5_SDK_11.0.0_89a8197
i am try to flash BLE with SPI code i am not able to flash the hex..while flashing...
Hello,
Recently I was using nRF Connect app to test BLE 4.2 Communication between my Android Device and nrf51422 board. updated the hardware device so the LE Secure Connections...
Dear Nordic Developer,
I can compile and ran examples of uart, saadc, pwm_driver, pwm_libraries. Now I would like to include uart in pwm_libraries to get inputs from PUTTY...
Hello,
I integrated the relevant code from the "uart" example into the "ble_app_uart" example(this is all the code in the main routine):
uint8_t cr;
uart_init();
...
Hi all:
I use sdk11.0
<nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay>
this example, scan heart sensor , sdk return...
It would be helpful to know how a packet looks like when transmitted/received from the NRF9E5 chip. I already found the algorithm to build the correct CRC, expected from the...
I have included the DFU service and a custom service in my application. During initialisation DFU service is getting initialised and later down the line my custom service...
Hello,
I have few question please about this example.
m_lesc_private_key looks unused, how to modify source to use a pre shared private key ?
is this exemple secured...
Hi!
We are trying a new module with NRF24l01+. We find a troublesome thing. On this video you can see the RF communication starts and stops with a broad-spectrum signal...
Hi :
In my application, i need to use 2 spi master (SPI0,SPI1) and spi slave the same time, but when i compiled drivers_nrf/hal/nrf_spi.h and drivers_nrf/hal/nrf_spis.h...
Hi. I'm using nRF528332, SDK13, S132.
I'm making multi-link peripheral refering to "experimental_ble_app_multiperipheral".
This example code says as below.
#define...
Hi Nordic,
In my application, I want to consume as less power as I can. In the initialization I have this functions:
static void utils_setup(void)
{
APP_TIMER_INIT...
