Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I want to use in my project tft 1.8 display with st7735 controller. I'd like to use some based code but can find nothing except on infocenter nordic
As I understand there...
Hi,
I am writing a boot loader which does not need to use the soft device as the image is being transferred over an SPI interface.
I have merged the softdevice and my...
Hi
I suppose that Multiple connection to centrals is available from BT4.1.
Is it possible to realize bu S110?
If it is so, which version is available the specification...
Hello, I made some boards on nrf52832 and I was testing the PCB.
The test program is ..\nRF5_SDK_12.0.0_12f24da\examples\ble_peripheral\ble_app_hrs.
(I have downloaded...
Hello! Just got a few NRF51822's.. looking to just brodcast a few basic URL's.. if someone can point me in the right direction or maybe let me know where I can hire someone...
I work with ble_app_uart example and want to move uart init and event handler into separate file( e.g uart.c).
I just copy uart_init, uart_event_handler functions with some...
I am writing code that runs on a NRF51822 (to be less specific it runs on a Red Bear Lab BLE Nano). The board has a 32.768khz crystal on it that I want to use to wake up the...
Now I am sending data at 250 ms.
I'd like to send data at 80 ms.
Is this possible?
also,how much can it extend the advertisement interval to the maximum?
thank you in...
i am working with eclipse to program the ble_app_hrs but it is getting error "No rule to make target _build/app_trace.o', needed by nrf52832_xxaa_s132'. Stop" when it builds...
Hi,
In the newer versions of NRF 5 SDK (sdk10 vs sdk12), does the softdevice takes more RAM?
I am using nrf51822 (qfaa) and sdk 12.3. with softdevice s130_2.0.0.1....
I can't get my PCA10040 board to send serial data when connected to a FTDI USB dongle.
When the FTDI dongle is disconnected, and I connect my logic analyzer to the tx and...
I have problem with PPI on NRF52832 (SDK 13.1.0, softdevice S132 4.0.2).
Programmable peripheral interconnect (PPI) usage by Softdevice S132 according to infocenter...
Hi all , I am beginning with SEGGER Embedded Studio . I flow 2 tutorial at :
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I using NRF52832 board...
My mobile set XOLO ERA 2 , bluetooth V4.0 is not pairing with bluetooth speaker MINI-X6, Bluetooth V2.1. While Bluetooth is on Mobile set gives message " CANNOT COMMUNICATE...
