I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi,
I'm trying to adapt the HRS/RSCS relay example from the SDK to use the Nordic UART service instead. Currently I can connect to the central just fine, but if I try to...
I'm using RTX timers on NRF51 and I'm getting a 7ms per second error. (I.e. osDelay(1000) takes 1007ms).
It appears that NRF_RTC1 is configured incorrectly in SDK examples...
Hello, I am working on NRF52 customer board + SDK_13.0.0_04a0bfd
I start with ble_app_uart example, I use interrupt tigger a repeat timer(500Hz, 400 times) to sample 6 channels...
I'm having major troubles with my debugging setup using a nRF51 DK (PCA10028 V1.2.0).
When I try to connect to the board I want to debug/program (which has an BlueMod ...
Hi Everyone,
I'm currently busy going through the OpenThread API and examples to better understand what all the functions do. However, I don't fully understand where the...
Preferences: nRF52832 chip, s132_nrf52_4.0.2_softdevice
Two or more nRF52832 chip are connected to iOS and Android.
And do bluetooth off in smart phone.
this case, bluetooth...
This suggests it should be possible to change the beacon advertising content in response to events such as a GPIO input.
I'm using nrf52 DK running the beacon example (SDK...
Hi,
What should I add to the makefiles to be able to generate an assembly code? Something similar to what is seen in the debug mode of Eclipse. I have tried -S/s but it...
Hi
I want to porting to nRF52840 but since S140 SoftDevice Specification documentation doesn't exist
I can not proceed with porintg.
I need S140's detail memory map...
I am using s132_nrf52_3.0.0_softdevice.hex and sdk12 and compiling with arm-none-eabi-gcc. The problem is that the bluetooth set up just jams at:
// Enable BLE stack.
...
I'm trying to get my nRF52 BLE peripheral to connect to my phone while its screen is off and it's in sleep mode. Other consumer BLE peripherals that I have can connect to...
Hello
is this possible to reset the timer.
for example i set the timer for 10 Second.
when he reach up to 5 second then i would like to reset the timer.
i found no function...
Hi,
I just noticed that my PTX and PRX projects use different assemblers and linkers -- not sure why. I got the sample projects from Nordic. What's the difference between...
I built my project on ble_app_uart peripheral example from SDK 12.2 and have added a display (Sharp LS044Q7DH01) using nRF52 as a SPI master to communicate. I think I have...
