to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi All,
I am new to the nRF processors (but not new to embedded progarming). Trying to use the evaluation board with the examples on the SDK. After realizing the freeware...
Q0. What IRQ Priority does BLE Has? and also what IRQ Priority does UART can have?
I'm guessing that from s130's document P65, Exception Model, It says,
Softdevice Timing...
Hello,
I could not set breakpoint in Eclipse. I set CFLAGS to -O0 and -g3 in Makefile
I am using GNU Tools ARM Embedded 6 2017-q1-update and Eclipse Neon3
Below are...
Hi,
is at the moment possible with S110 (nRF51 SDK) to whitelist only SOME of bonded peers? I need to allow connection from one selected central. Selection is made by user...
As a follow up from devzone.nordicsemi.com/.../ , I am now trying to find out if I am getting all of the memory settings put together correctly. When I have them at higher...
I am using nrf51822, 16K RAM, 256K Flash.
From the movie , there is no way to secure my firmware for DFU. Is there any other way to secure my firmware?
Thank you
I know the many differences coming in bt5. Will the programming concepts be the same in the upcoming 5 version? IF my code is working with ble4.1 will it automatically work...
After a bunch of headache I was able to successfully program with the nRF51822 Development Kit without the nRFgo Starter Kit motherboard, here is how I did it.
Hardware...
I'm working on a design that incorporates an nRF52832 along with some sensors and drivers.
Up to this I've been sacrificing power consumption in prototypes by using LDOs...
Hello,
Is it possible to change SPI baud rate whenever we want?
For example:
The initial SPI baud rate is set to 4M. We want to change the baud rate to "2M" to get...
Hi,
This may be stupid, but I can't declare classes in my .h file in keil. I have arduino library for my I2C device, but keil; does not recognize when I declare classes...
I've looked through and tried many examples on getting my SAADC to produce a temperature offset. About a month ago I had the SAADC working really well with a wheatstone bridge...
Hello,
What changes need to be made to the following tutorial to enable basic advertising with the Rigado BMD-300 on a custom board breakout board?
devzone.nordicsemi...
Hi,
I have multiple devices set up in a simultaneous peripheral and central mode that exchange data on connection. As there may be multiple devices around, I want to make...
i download the sample code (\examples\nfc\record_text) to pca10040,it can be detected by NFC reader,the serial number is 5f:46:ac:eb:75:a7:ea,if i want to change this number...
