I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
I'm trying to control LSM6DS3 by TWI communication.
Slave address of the chip is 0xD4 when SDO/SA0 pin is low.
I'm using SDK13.0.0.
My code is like below.
...
I will test the receiver blocking of ETSI with the nRF51822 module
(EN300328 V2.1.1 2016-11 5.4.11 Receiver Blocking).
However, please tell me the next items because I do...
I'm testing the setup for the Receiver Blocking test ask part of EN 300 328 V2.1.1 and I have a question after reading these posts devzone.nordicsemi.com/.../ , devzone.nordicsemi...
Hi,
We have some custom boards with NRF51822 and the S110 (v8.0.0) softdevice, on which we have programmed the dfu dual bank bootloader, based on the example one from the...
Hello Nordic,
Im using SDK13.0 and im struggling with pm_peer_delete()
My way of testing this function:
Raw firmware without any bonds.
Create bond. Peer id is...
I download my program to PCA10040 DK board and the program will make the led1 blink two times.
First I download program to flash and all work well.The led1 will blink two...
Is it possible to upload a SoftDevice over BT onto a fresh, brand new chip, or must one first flash a specific OTA-compatible FW onto the device via UART/JTAG with a SWD programmer...
I found a problem using the RTC2 on the nRF24le1 which i dont know how to solve it.
I am using the RTC2 on the master to generate a TICK interrupt exactly every 1s. With...
Hi,
I am newbie to NRF52 devices. My scenario is, I want to create a split keyboard which is left-hand part and another is right-hand part. Both 2 parts are wireless. I...
Hello. I recently bought this nRF51822 module www.ebay.in/.../252563375286
And I have a nrf51 DK PCA10028 with me. I am tried to upload codes to the module following the...
I'm prompted to select the target device for a new uVision project. As far as I've found so far, they both are the larger memory variants (256KB).
segger.com/jlink_supported_devices...
Hi,
How can one calculate the distance between two beacon based on RSSI values?
How can one find location based on RSSi values of the beacons ?
What are short comings...
I tried the Bjørn's code : devzone.nordicsemi.com/.../
I didn't make it... Could you help with a simple code you've tried for adxl345 ?
Thank you
Yassine
Hi Nordic!
On the radio_test example, the functions scanf and printf are heavily used, however, I haven't found where they are defined. This example is reading the data...
I really need your help regarding a problem. I developed my own pcb with nrf52 and verified it with your hw engineer. I just finished soldering and hooked it up with your...
