We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
hi guys. i'm have a project with nrf52832.
i use jlink v8 debuger clone form china, just 12$ and have this troulbe in this figure
Untitled.png
could you help me?. jlink...
Hi,
I was trying to write the s132 SoftDevice from the nRF5_SDK_13.0.0 onto the Sparkfun nRF52832 breakout via OpenOCD and an ST-Link v2 debugger. The SoftDevice flashed...
Greetings -
I am working on a peripheral-heavy project. Many of the devices seem to work Just Fine with VDDio of 1.8 volts. On device seems to be having fits and I need...
void Gzll_TxSuccessCallback(uint32_t pipe)
void Gzll_TxFailedCallback(uint32_t pipe)
More than two functions are not accurate judgment
GZLL agreement return function cannot...
I try to implement this library to my code.
uint32_t settings_set_erase_flag(int32_t flag)
{
uint32_t err_code = fds_write(flag, ERASE_BOND_FLAG);
return err_code;...
Hello I have this error:
Checking installed packages
pyside: 1.2.4
pyqtgraph: 0.10.0
numpy: 1.12.1
pynrfjprog: 9.0.0
Warning: The software is tested with PyQtGraph...
I wrote a peripheral similar to NUS. Then I use the multilink central to connect to 3 of them. First two are fine. But when the 3rd is added, the 3rd one would connect, but...
Hi,
I want to make an BLE_UART dongle which will receive the data from the module(An external module is connected through UART) and it will be send over the BLE to ble_receiver...
I'd like to write some timestamps to a log variable in order to see how much time has elapsed between certain points in my code. app_timer.h has two functions that look suitable...
Hello,
I have a problem while combining peripheral examples in SDK13. I am trying to combine twi_sensor and uart but when I do this in uart folder, compiler gives following...
Hi support team,
We met an issue for connecting our device built in nRF51822 to Android device.
The nRF51822 uses below firmware program:
nRF5_SDK_12.3.0_d7731ad...
Hello,
I am working UART_BLE_APP , my query is when we transfer the data form smartphone application to the device where the data will get stored in device and can we access...
I have created a characteristic for sending up to 60 data bytes in a buffer using a sequence of 20 byte notifications sent to an external device. This works quite well for...
Hi,
What is an optimal transmission power to maximize the coded PHY range, but still stay within ETSI regulations? Can nRF52840 actually exceed the regulations if I set...
Controller:
nRF52832-QFAA
Reference project:
nRF5_SDK_11.0.0_89a8197/examples/dfu/bootloader/pca10040/dual_bank_ble_s132
Question:
The idea is, to store a init_DFU_by_flag...
