Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi, Nordic!
We have two PDK-NRF52840 and custom boards with NRF52840 chips.
2 from 5 chips have a broken bit in RAM. This is different places.
For example:
Is this...
Hi all,
if i buy 2 nrf52840dk:
Is possible create an audio connection like intercom between the two dk?
Can I send my voice from "dev board 1" to "dev board 2"?! and...
Hi,
I beginning now to program nrf51822. I would like to let the nrf51822 wake up after 3 hours by using a software timer interrupt.
Should I use power_manage()? Before...
Hi,
I'm trying to configure custom local GATT server on nRF8001 device. I added a custom service with multiple characteristics, but I can't generate source files. It says...
Hello!
I'm doing master thesis and I've chosen WT51822-S4AT board for BLE. I've made board successfully and programmed uC to send serial data to BLE.
I'm able to received...
Hi all,
I am using nRF52832 DK for my project. I need to config BLE for connecting with my phone. After a lot searching, I know that I can use softdevice API for configuring...
I mashed up RTC and SAADC examples. The files of the project are attached in the end of the post. The problem is that after the first iteration (I want to sample audio for...
Hello,
I am using developping on an nRF51822 with SDK12. In our application, our custom board need to communicate with a computer through a USB communication. I am not...
I'm working on the product using the nRF51422 QFAAE00 , SD110_nrf51_8.0.0, SDK 10.0.0. My product has the advertising flow as below
The device advertises forever...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
Hello,
I need help about the multirole with the Freertos.
When I take the code example from Nordic "C:\Nordic\nRF5_SDK_13.0.0_04a0bfd\examples\ble_central_and_peripheral...
