Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello!
I have:
nRF52840-Preview-DK (pca10056)
nRF5_SDK_13.0.0_04a0bfd (s140)
I load **nRF5_SDK_13.0.0_04a0bfd\examples\ble_central\ble_app_uart_c\hex\ble_app_uart_c_pca10056_s140...
I have an interrupt coming in every 50-150 microsecs and I want to measure these intervals as precisely as possible.
I tried this with SDK12.2:
APP_TIMER_INIT(0, 5,...
We're trying to bit-bang SWD to program an nRF52832, and we're running into some problems getting the nRF52 to respond. One theory is we're not generating a high enough clock...
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
Hello,
I've noticed the following sentence in s132_nrf52_3.x.x release notes:
"Synthesized low frequency clock source is not tested or intended for use with the BLE...
I'm following the tutorial in the NRF52840 SDK on setting up a Thread Border Router here and I've run into some issues during testing. For one, I'm trying to resolve ipv4...
Hi,
I'm able to successfully enable Access Port protection, either using nrfjprog or by setting NRF_UICR->APPROTECT register to 0xFFFFFF00 in code.
But I have a problem...
Hello,
Since this seems to be a very hard topic to find info about (its very contradictory and confuse) I'd like to ask a Nordic employee directly.
I'm planning to build...
This concept keeps popping up when I'm dealing with mesh networking.
My guess is that, to avoid air collision, packets/pdus are sent on a randomized or predefined combination...
Hi,
I am using ble_app_uart for my development, in that I have buffer size of 2kB which will store all the incoming data and the data will be processed and send over NUS...
Hi all,
I am using an NRF52 and SDK 13.0
I have an external device (central) that I am connecting to using my (peripheral) device.
My peer manager set up is
#define...
Hello All,
I've got two Rigado development boards that I'm programming with KEIL uvision 5. I've tried a few examples, for example: blinky, which program and work fine...
Hello
I want to clarify the exact meaning of the carrier test or unmodulated signal in DTM.
In carrier test mode, DUT transmits 0xFFF....FFF which means all one pattern...
