Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I would like to update ble device name from device1 to user2.
How i can do this in swift language . i m atrung to update by ios app.
is below way is right? but not able...
Hi Nordic,
I was reading the Wiki page for porting OpenThread to a new hardware platform ( github.com/.../Porting-Guide) and I noticed there isn't a "flash.h" header file...
MIN_CONN_INTERVAL
MAX_CONN_INTERVAL
SLAVE_LATENCY
CONN_SUP_TIMEOUT
Hey guys,
I want use my device with Android as well as iOS, but i am facing some issues for...
Hello, when reading the source code for a mesh node provisionee, I stumbled upon this MACRO function:
NRF_MESH_ASSERT
Edit: it is in ble_mesh_v0.9.1-Alpha\mesh\src...
hello,
i am experiencing issues with the TWI library on the smart beacon kit rev. 1.3.0 which features the v3 of the nRF51822. i had the same experience on the new nRF52840...
Hi. I'm trying to flash Secure DFU bootloader together with my application. I tried to flash bootloader and then main application, but the device stays in bootloader instead...
ppi.zip Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. Even after allocating the access address of Bluetooth on line 196 as set_address0...
Hi there,
I am trying to measure environment below 0 C but the app reboots and refuse to connect with thingy52 at lower temperatures. Do I have to set up anything else...
hi ,
I have a question about rtc.In my project ,I use rtc1 for app timer and rct0 for low_power_pwm.The problem is that I dont't have any idear to enable rtc0 instead of...
hello:
i meet some trouble,i can find the service,then appear error "BLE_GATT_STATUS:10a".
#define BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND 0x010A /**< ATT Error: Used...
Hi,
I am trying to use the nRF51DK (PCA10028 v.1.2.2).
I cannot get Windows 7 to recognize it via USB reliably. I have JLink v6.16a installed and when I plug in the board...
I have variable values coming out of a terminal at all the time. I using this command:
void in_pin_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
...
Hi All,
I am developing a ble applications and am unable to get pins 9 or 10 to work as gpio. I understand that this is because, by default they are used by the NFC.
...
