I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Good morning,
Based on different articles, I set up a nrf52832 with S132 3.1.0, the secure bootloader found in "SDK_12.2.0/examples/dfu/bootloader_secure" and the buttonless...
Hi together,
I'm using nrf52832, SDK 12.1.0 and S132 3.1.0.
I integrated the peer manager to my application code and have the following questions concerning the bonding...
Hi,
I noticed a possible issue in BSP_MS_TO_TICK macro computation.
In bsp.c, the macro is defined as:
#define BSP_MS_TO_TICK(MS) (m_app_ticks_per_100ms * (MS / 100...
Hi nordic,
Is there any ways to implement that my device connect with one special Central Device likes Andriod phone and Iphone. Currently I know is whitelist. First I add...
Hi;
Is it necessary to reset SoftDevice when using NVIC_SystemReset ()?
The SoftDevice must only be initialized if a chip reset has occured.
I saw the above comments...
Here is the code I'm using to test it out:
static float number = 0.5678905;
NRF_LOG_INFO("Float number: "NRF_LOG_FLOAT_MARKER"\n\r", NRF_LOG_FLOAT(number));
And...
Hello,
I am working on NRF52382 custom board, where I am running a timer of 30 sec to get a value every 30 sec.
I want to save this value in flash.I am well aware of...
Does the s210 softdevice not function on the nRF51822? I see it available for the nRF51422 here but it is listed under the 51422 only.
I have a v1.1.0 PCA10031 (nrf51422...
Hello,
I developed an application for the nrf51822 Smart Beacon, SDK11 s130, that basically advertises the battery lvl of the beacon, the staus of button_1 and the number...
I have a nRF 52 DK board. I have flashed dtm example onto it. I have connected a USB to serial UART interfacing board ( www.sparkfun.com/.../12731) to the respective Tx, Rx...
Both the capacitive touch library and the driver (which is better ?) are using the analog inputs.
There are only 8 of them , and we need 10 at least buttons.
Is there...
I'm migrating from SDK11 to SDK13. My custom service is based off Heart Rate Service, so I started from the new SDK13 example of HRS, and updated all the initialization code...
Hi,
on Android, I sometimes get delayed notifications. I measure realtime data and send them over notification, and I can see data change on Android with approx 1 s delay...
