Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
i am trying to connect via bluetooth using the gatttool on a Raspberry Pi. On the Nordic device I am using the BLE Proximity Demo. Everythings work fine, but after 30...
Hello all,
I am trying to get a communication between the nRF8001 and the nRF51822 using the UART service. The nRF8001 is connected to an Arduino and is working fine. I...
I am trying to find out the issue with my nonvolatile driver. I currently try running
nrf_nvmc_page_erase((uint32_t)(page_address));
However, that doesn't seem to...
I've been testing Pre-Production samples running a firmware in which I catch any and all Error codes or Reason reasons and write them to the gpregret register to be read later...
Hi, I am using a modified version of RBC mesh.
When I connect with an external device to one node using BT I get connected but I can get randomly disconnected when data is...
So, I'm trying to work around the Ble Uart example, using the PCA10003 Board. The example uses one of the buttons as a "Wakeup" source, but during the bsp_init() call, the...
Hi Nordics,
I would like to run the app example “ble_app_hrs_s110_hci_pca10028 (nRF51 PCA10028)” on the 32 MHz crystal. Can anyone help to change the code to 32MHz base...
Hello,
I am currently use the new SDK 8.0 for the NRF51822 (S110 soft device). I noticed that on SDK 7.0 for the ble_gap_sec_params_t struct , there was a variable called...
I want to see register values in interrupt service routines after a timer timeout. However, when I enable debugger in Keil, it only iterates once to the end of main function...
I've been trying to get a simple blinky program to compile for the better part of a day now. The makefiles are outdated and so are the keil projects. Is this SDK no longer...
Hi ,
I have a code like below.
__attribute__((used, long_call, section(".data"))) void function_1()
{
unsigned int a;
unsigned int b[10];
int c;
c= a-(...
I currently have an application with DFU bootloader that runs on s110 5.2.1 on a rev1 nRF51822. If I upgrade to the latest rev3 chip, can I just flash it and everything will...
How can I compile a simple blinky program for the PCA10024 with the IOT SDK, and using the (iot modified) s110 softdevice?
I've been trying to get a simple blinky program...
Hi all,
I am facing a problem with pstorage_init() function. In fact after enabling the softdevice (S130), I am calling the pstorage_init() function. When debugging, the...
