nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Hi support !
In my current application, I use nRF24L01+.
I want to change this nRF24L01+ for a nRF51422 to add BLE connectivity.
So, I've started my development with...
I'm using SDK 7.1, PCA10028 eval board, SD110 7.1, MCP 3.6.0.8331
I have 2 characteristics, and both are 32 bytes long. When I try a "Write Long" from the MCP a
BLE_EVT_USER_MEM_REQUEST...
Hi,
Merry Christmas!
I have a question about pstorage_store.
Actually, I want to store some data in the memory. Each piece of data has its own size (between 1 byte to...
Can I config AIN0 and AIN7 as the input pins of ADC, and config P0.01 and P0.02 as TWI, and config P0.03 and P0.04 as GPIO?
Or I must config ALL AIN PINS as ADC?
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
I've followed the steps mentioned in this thread devzone.nordicsemi.com/.../ and everything seemed to work fine. I've successfully uploaded "nrf51822_beacon_app.hex...
Hi.
I read in the sdk documentation, there is a library to use MPU-6050.
So i try to find it but I did not succeed.
i want to read data from 6050 and send this data with...
Hello.
I want to use nRF51422 chips to make some kind of mesh network using raw radio stack (NRF_RADIO) with my own protocol on the top of it. In reference manual there...
Hi,
I am a new comer to the nRF8001.
I am using Redbear Blendmicro (nRF8001) for my project.
I have wrote a apps to scan my Blendmicro(s) and acquire their RSSI value...
I use direct input AIN2 pin battery 3.3v, the other pins are not connected to anything, I did not enter into ADC_IRQHandler,may ask about what the problem it
this is my...
Has anything changed with the Bluetooth LE in iOS 8? I have an ANCS library for Arduino ( https://github.com/robotastic/ANCS-Library ) that was working fine with iOS 7. I...
I'm trying to program nrf51822 via st-link and open ocd.
Here command:
openocd-0.8.0.exe -f interface/stlink-v2.cfg -f target/nrf51_stlink.tcl -c "program address".
...
dear all:
I have 2 kind of board that are PCA10006 and PCA10028,
but I find out the IoT example can't be run on PCA1006,
what are different between PCA10006 and PCA10028...
