Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello,
What is he meaning of PROTENSET0, PROTENSET1 in sd_flash_protect()?
How can I use this function to set WRITE PROTECT to a certain flash page?
I searched a lot...
Hi,
I need to use nrf51-ble-app-lbs application example to add my customized applications. I have downloaded the project but I'm not able to compile it probably cause I...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
I have read many times about how BT LE allows devices to run for more than a year on a coin cell.
However, the least current consumption I can obtain while connected is around...
Hello,
We are developing a system using a receiver nRF unit, and multiple transmitter nRF units. The transmitters use the proprietary radio protocol (not bluetooth LE)...
Hello,
I am trying to flash an application onto nRF8122 from an android mobile using the Nordic app. After pressing the DFU button, the programming fails giving a pop as...
I've been looking for information on GCC support for the DFU bootloader examples in SDK v7.2.0 for the BLE Dongle board(PCA10031) but unfortunately there's nothing in the...
Hi
I'm testing the nRF Toolbox for Android. But I get this error when I try to connect using the proximity feature:
I'm using the nrf51822 EK with the s110 ble_app_proximity...
Hi Nordic Guy,
I'm trying to fine tune my connection parameters for better battery life, while at the same time trying to keep them within Apple's guideline. I notice in...
Hello guys, I'm going to start programming for nRF51822 and I want to ask you something.
I'm going to start coding for mbed HRM1017 which is the simplest eval board I found...
I'm attempting to use a custom UUID as outlined in nAN-36. I get an error (NRF_ERROR_DATA_SIZE) when I call ble_advdata_set . Specifically:
ble_advdata.c::uuid_list_encode...
I have a bluetooth hub (NRF51) as central and a wearable device (NRF51) as peripheral. What I need is that as soon as a smartphone enters the range the peripheral let's go...
Hello,
I'm redrawing and routing my own PCB for nRF81x22. I take the details from pca10028 files.
My question: Can I route the PCB with only 2 layers?? I have seen only...
Hello,
I had to use sd_ble_gap_address_set() to make sure, that a bootloader running on the same device will not be cached on OS/X:
static const ble_gap_addr_t gap_addr...
This may be a newbie question, but it had puzzled me for a while now.
Looking at the PCA10031's schematics i can see two leds been used.
LD2 i can figure out. Datasheet...
